Question about Magic Sing Along Consumer Microphone

1 Answer

Wiring diagram magic mic 501

.i don't know where the wires go

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 165 Answers

Hello saleem in order to help you load up some pictures best regards antonio

Posted on Dec 29, 2013

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
night71
  • 328 Answers

SOURCE: Worn out wires

I found this shop on the net.
http://www.webbyshop.com/shop/pid213/enter-tech-magic-sing-rca-cable.html

Posted on Oct 30, 2007

seandc
  • 18 Answers

SOURCE: ED 8000

You need to replaced the "voice coil". that thing that youve been desoldering and soldering is the voice coil. It has two wires- white and black. it is already grounded and need to be replace (the fact that it humms..). my company distribute wow magic sing here in Philippines and we can easily repair that.

Posted on Mar 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wire 4 pin Turner Plus 3 Power Mic for cb radio to 5 pin President Washington SSB AM Radio


the best i can find is this
red pin 5 ptt
black pin 4 ptt ground
white pin 1 mic
shield pin 2 mic ground
no connection pic 3

Jan 19, 2015 | Radio Communications

1 Answer

Magnum delta force radio wiring diagram for Mic turner 2pluse 2


Must know the pin out of the transceiver your wiring it too.
like cobras 1.ground 2.audio 3. TX 4. RX... then wire accordingly.(same as the 4 pin exports)..
Use a ohm meter to find the correct wires on your mic switch.
then you know how to wire any mic to any transceiver.
This will work for the turner 2+2

Aug 24, 2014 | Radio Communications

1 Answer

Will a diesel 360-3 mic ork on a galaxy dx99v



  • Hi, I can help.

  • The Diesel Electronics CB will work but you have to wire it as stated below.

  1. #1 Shield and Black - Ground
  2. #2 Yellow - Audio
  3. #3 White - Transmit
  4. #4 Red - Receive

  • I don't know if anyone before you has re-pined that mic or not so if you just remove that little Philips screw at the mic connector and then give it a quarter turn you can slide the connector out and take a look and compare the wiring. The actual numbering for the pins on the Galaxy 4 pin mic connector is as indicated below in the diagram. As you look at the mic tip make sure the indent on the mic is as it is the diagram.
ironfist109_269.jpg


  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.

Regards, Tony

Sep 22, 2011 | Galaxy Radios DX-99V 40-Channels Base CB...

2 Answers

Hello........ looking for a schematic for Bose 501 series 3 speakers. I need to replace the fuse in line with the tweeters.... its blown & does not have a value on it (unmarked, quick blow, twin lead,...


Did you find a solution? Dunno if it's much help, but I just today picked up some 501s - Series I I think - ugly heavy brown material grilles - but with a manual! No fuses in these, but booklet recommends installing your own in-line fuse holders (!?). Specifies a BUSS AGC-3 fuse for amps under 50wpc; or a MDL-2 fuse for amps over 50 wpc. Can be placed is series with either or the two signal wires. Very strange.... Robin

May 14, 2011 | Bose 501V Speaker

1 Answer

ED 8000


You need to replaced the "voice coil". that thing that youve been desoldering and soldering is the voice coil. It has two wires- white and black. it is already grounded and need to be replace (the fact that it humms..). my company distribute wow magic sing here in Philippines and we can easily repair that.

Dec 25, 2008 | Magic (ED8000) Professional Microphone

6 Answers

Mic wiring diagram


Same as Omega
#1 Mic Audio
#2 Receive
#3 Transmit
#4 Up/Down for channels
#5 Ground/Shield
#6 13 volt

Jan 13, 2008 | Magnum DeltaForce CB Radio

1 Answer

Worn out wires


I found this shop on the net.
http://www.webbyshop.com/shop/pid213/enter-tech-magic-sing-rca-cable.html

Oct 30, 2007 | Magic Sing Along Consumer Microphone

Not finding what you are looking for?
Magic Sing Along Consumer Microphone Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Magic Audio Players & Recorders Experts

Michial Gueffroy

Level 3 Expert

1138 Answers

conquer111

Level 1 Expert

5 Answers

T-Comtech Repairs
T-Comtech Repairs

Level 2 Expert

417 Answers

Are you a Magic Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...