Question about Amana PTH123B25AJ Heat Pump Air Conditioner

Open Question

Manual reset ptac unit - Amana PTH123B25AJ Heat Pump Air Conditioner

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 49 Answers

SOURCE: Amana PTAC

Sounds like if this is a heat pump, maybe it tripped out on high pressure. Maybe just unplugging the system may reset the control boards. This maybe due to a dirty filter or dirty evaporator coil.

Posted on Nov 18, 2007

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

PTC123D35ARDA SERVICE MANUAL


Try this:
http://www.amana-ptac.com/Portals/3/PTAC/PDF/IO-PTAC2.pdf

Dec 02, 2014 | Heating & Cooling

1 Answer

My amana ptac is not heating....the code "np" is displayed....how do I correct this...we just installed the unit and know little about operation. Thanks


I don't see this error code in the manual. I do see nP as an error code for Window Switch lockout. I just had this happen to me and they had me reset the control board.

Remove case, flick master switch to OFF for 10 seconds. Press Heat/Cool same time turn switch back on HOLD until off light comes on.

You should be fixed. Just had to do this for my unit. I was playing around with the settings and turned on the window switch option by accident.

Feb 02, 2013 | Amana In Wall Install Kit For Digismart...

1 Answer

Freidrich ptac won't start


Check for a reset or circuit breaker on the unit.

Jun 14, 2012 | Friedrich PTAC (PDH09K35B) Air Conditioner

1 Answer

Compressor runs continuously regardless of temperature setting. How do I replace the thermocouple in the unit?


I doubt that thang havind a thermocouple. Too new. Must have a thermister. A thermister changes in resistance as temp changes around it. The control monitors the change and shuts down the ac when the desired temp is reached. It is either going to be the thermister OR the control. If you do not know which it is you go with the cheapest part first right? I have a PTAC manual but it ain't an LG. I would be willing to bet though the same folks made this one. It will at least give a clue what to check on this beast: PTAC service manual

Aug 21, 2010 | LG PTAC LP070CED Thru-Wall/Window Air...

1 Answer

Carrier PTAC Condenser ices over.


You are describing normal operation for a heat pump unit.

Feb 20, 2009 | Carrier 52CQ315 Air Conditioner

1 Answer

Amana PTAC PTC093A35AA won't blow heat


The reset button is located behing a panel on the front of the unit that is labeled Heat Reset. If that label is gone then look around, it is a small hole, small enough for a paper clip to fit through.
That being said, I have 137 of these units in one of my hotels and have not had a single one needing to be reset. You probably are going to need a new control board kit. These can be purchased from Amana. They are $130. Make sure that you have pulled the heater coil out and inspected it first. Also, there was a recall years ago where Amana was supposed to contact and send out new voltage switches. These are the round black things that the Brown heater wires connect to on the upper and lower side of the heating coil. You should also try to replace those if you find the coil in good condition. I have had those resolve heating issues. Most of the heating issues were a result of a bad relay on the control board though.
Please remember to rate this fix.

Jan 23, 2009 | GE Zoneline AZ38H12DAD Split System Air...

2 Answers

PTAC UNIT QUIT WORKING


If you have a clamp tester, operate the unit with the clamp tester and check the current reading. If the current reading is normal but the reset button is tipped then there is something wrong withe power plug reset button. But if the current reading is higher than the name plate rating then there is something wrong with the unit.

Mar 09, 2008 | GE Zoneline AZ38H12DAD Split System Air...

2 Answers

Amana PTAC


Sounds like if this is a heat pump, maybe it tripped out on high pressure. Maybe just unplugging the system may reset the control boards. This maybe due to a dirty filter or dirty evaporator coil.

Nov 18, 2007 | Amana PTH123B25AJ Heat Pump Air...

Not finding what you are looking for?
Amana PTH123B25AJ Heat Pump Air Conditioner Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Amana Heating & Cooling Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Donni Steen

Level 3 Expert

659 Answers

Bill Long

Level 3 Expert

587 Answers

Are you an Amana Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...