Question about HP Compaq FS7600 17" CRT Monitor

1 Answer

Full screen on monitor

I was making adjustments in display---I did something and
screen now is not full screen display there is an inch of black on
either side and a 1/2 of black on bottom of screen

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 93 Answers

You can use the menu and adjust the vertical size.or if did already but it doesn't work,try to open your monitor and look for a trimmer in the vertical section,then try to rotate by these you can adjust now the vertical size
 

Posted on Oct 18, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

ERROR CODE AND POWER SUPPLY CIRCUIT


Viewing the Self Check Diagnostic List
1. TV must be in standby mode. (Power off).
2. Press the following buttons on the Remote Commander within a second of each other:DISPLAY > Channel 5 > Volume - > TV POWER .
Results for all of the following diagnostic items are displayed on screen. No error has occurred if the screen displays a "0".
NOTE: If the Service Menu display text is not completely visible, press the Menu HOME button on the Remote Commander to refresh the display.
3. To exit Self Check display, turn the power off. Press [Menu] Exit.
Clearing the Self Check Diagnostic List
1. In Service Mode, press the Channel 8 Channel 0 .

RESETTING TO FACTORY DEFAULTSUse the following instructions to restore the User Controls and
Channel Memory settings to the preset factory conditions.1. While holding down the UP ARROW on the Remote Commander, press the POWER button on the right side of the set.The set restarts and displays the initial setup screen. This may take several minutes.
White Balance adjustment
1. Allow approximately 30 minutes for the set to warm up before proceeding with the white balance adjustment.
2. Connect the signal source to the 3 terminals of the Component In input (Y/Pb/Pr).
3. Set the Picture Mode to "VIVID" in the user menu.
4. Select the Component In input.
5. Open the Factory Service Menu (see section 3-1.) and select "Service Alignments Menu".
6. Set "White Point Red", "White Point Green", "White Point Blue" and "Black Level Offset Red", "Black Level Offset
Green", "Black Level Offset Blue" to average values .
"Cool " White Balance Adjustment
1. Select "COOL" from Color Tone in Service Alignments Menu.
2. Input 70IRE full white pattern signal into Component In.
3. Adjust "White Point Red", "White Point Green", "White Point Blue" in Service Alignments Menu if needed.
4. Input 25IRE full white pattern signal into Component In.
5. Adjust "Black Level Offset Red", "Black Level Offset Green", "Black Level Offset Blue" in Service Alignments Menu if needed.
6. Repeat steps 2 to 5 to achieve desired White Balance.
FOR MORE DETAILS CHECK THE FOLLOWING LINK
www.electro-medical.blogspot.com
google.com/+AjinGopakumar

USE SEARCH TAB TO FIND MODELS OR USE THE DROP DOWN MENU

on Jun 30, 2015 | Sony Bravia L-series Kdl-32l5000 32-inch...

Tip

SERVICE MODE AND ERROR CODES CHECK


Viewing the Self Check Diagnostic List
1. TV must be in standby mode. (Power off).
2. Press the following buttons on the Remote Commander within a second of each other:DISPLAY > Channel 5 > Volume - > TV POWER .
Results for all of the following diagnostic items are displayed on screen. No error has occurred if the screen displays a "0".
NOTE: If the Service Menu display text is not completely visible, press the Menu HOME button on the Remote Commander to refresh the display.
3. To exit Self Check display, turn the power off. Press [Menu] Exit.
Clearing the Self Check Diagnostic List
1. In Service Mode, press the Channel 8 Channel 0 .

RESETTING TO FACTORY DEFAULTSUse the following instructions to restore the User Controls and
Channel Memory settings to the preset factory conditions.1. While holding down the UP ARROW on the Remote Commander, press the POWER button on the right side of the set.The set restarts and displays the initial setup screen. This may take several minutes.
White Balance adjustment
1. Allow approximately 30 minutes for the set to warm up before proceeding with the white balance adjustment.
2. Connect the signal source to the 3 terminals of the Component In input (Y/Pb/Pr).
3. Set the Picture Mode to "VIVID" in the user menu.
4. Select the Component In input.
5. Open the Factory Service Menu (see section 3-1.) and select "Service Alignments Menu".
6. Set "White Point Red", "White Point Green", "White Point Blue" and "Black Level Offset Red", "Black Level Offset
Green", "Black Level Offset Blue" to average values .
"Cool " White Balance Adjustment
1. Select "COOL" from Color Tone in Service Alignments Menu.
2. Input 70IRE full white pattern signal into Component In.
3. Adjust "White Point Red", "White Point Green", "White Point Blue" in Service Alignments Menu if needed.
4. Input 25IRE full white pattern signal into Component In.
5. Adjust "Black Level Offset Red", "Black Level Offset Green", "Black Level Offset Blue" in Service Alignments Menu if needed.
6. Repeat steps 2 to 5 to achieve desired White Balance.
FOR MORE DETAILS CHECK THE FOLLOWING LINK

www.electro-medical.blogspot.com
google.com/+AjinGopakumar

USE SEARCH TAB TO FIND MODELS OR USE THE DROP DOWN MENU

on Jun 30, 2015 | Sony Bravia KDL-26L5000 26 in. LCD HDTV

1 Answer

My picture display is narrow and does not cover the screen.


Does the Genie box have screen settings in in? Sometimes hd will show in smaller screens. Makes the picture nicer. If you adjust the screen size with your remote the high definition "niceness" will not be there.

Jul 30, 2014 | Seiki Televison & Video

1 Answer

How do i make it full screen?


Look in the settings for apex then adjust the wide and t in there.
Terry

May 02, 2014 | BenQ G2250 21.5 Full HD LCD Monitor BENQ

3 Answers

Acer v223w monitor can not get full screen. windows 7


Hi,
Sounds like driver related problem,
click here: Driver Update and try to update your drivers.
Cheers
Brian

Mar 30, 2012 | Acer V223W

1 Answer

I have a toshiba 40 inch flat tv. I cannot make it full screen. It is as if it has black margin around the picture making it appear like a 32 inch tv. What do I do?


If this is reffering to having a pc/laptop plugged into the screen, try starting the computer with the tv already plugged in and on the correct channel. If this doesn't cure your problem then try setting the screen resolution in your display properties. set to 1920x1080 or 1280x720, this should cure your problem, if this is not a computer related issue, have a look in the display settings for your tv and see if there is a resize option or similar to adjust the image size.

Hope that this helps.

May 08, 2011 | Televison & Video

1 Answer

H243h screen not using its full space on the


Control panel-Appearance and themes-Display-Settings-Advanced. Then adjust to suit

Apr 09, 2010 | Acer 22" X223w LCD Monitor

2 Answers

Monitor will not display full screen.


Usually there is a adjustment tool built in with your monitor who let you adjust this. You will be able to move it up-right-left-right along with a few other options about brightness/contrast, gamut and so on. Let me know if you still need help with this

Jun 08, 2009 | Acer X203W 20" LCD Monitor

1 Answer

I have a 1 inch on the left and right side how do I get full scre


if you hav a monitor separate from your computer(not a laptop)then just use your settings on the monitor untill it works again the way you like it..

or for laptops and monitors with no controls on them go 2 control panel>>>>appearance and themes>>>>display. then click on the tab that says settings. go 2 advanced and the dpi setting should be set at 96....and if nothing changes go 2 the appearance tab then 2 advanced. and at the bottom for the item look for active window border and the size should say 1. if it does then keepo trying to make the number bigger so your page doesnt have a black border

Nov 30, 2008 | Gateway Computers & Internet

Not finding what you are looking for?
HP Compaq FS7600 17" CRT Monitor Logo

Related Topics:

299 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

pontelemon
pontelemon

Level 3 Expert

538 Answers

Alun Cox

Level 3 Expert

2678 Answers

Are you a HP Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...