Question about Hobart SR24C-4 Undercounter Dishwasher

1 Answer

Water level stays to high, everything else is working fine. just does not go down low enough and next cycle pushed water out over the lip at the front

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 109 Answers

Two issues.
the first is a retricted drain . either the hose is kinked or a blockage at the drain valve, or where the hose joins the sink plumbing. disconnect it from the plumbing and let it run into a bucket to observe the flow.
The second is, the float protecting an over fill is not shutting off power to the fill solenoids in the event of over filling. Try raising the front feet and keeping the rear as low as possible to bias the water to the rear of the tank.

Posted on Mar 23, 2014

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Hobart AM-14 water temperature not maintained

Hobart AM-14 will wash and rinse in manual, but not in automatic

Posted on Dec 10, 2009

  • 37 Answers

SOURCE: my lxi dishwasher drains more

There are two different styles of lxis one style has a drain diverter valve probably messed up some how something stuck in it not diverting the water to the wash arms and instead pumping right down the drain I am guessing this is your problem.There is actually a little black washer in the body it is controled by a dc solenoid .washer probably come off and is gone you will have to replace the whole drain body.This drain body is a real pain to change.Not easy but it can be done.If you change it yourself get the two new short hoses that go to it it will make things easier.But pull it out before you buy anything it could just be jammed.You can reach under the machine trough the front bottom plate where the gauge is located and move the flap by hand to see if it moves.TURN OFF ELECTRIC this little dc solenoid will give you a good zap.after doing that turn electric back on.leave cover off and look under with a fashlight.live wires will be exposed keep hands clear fill machine wait for it to stop.then turn it off it will drain when finished the solenoid will click three times.this is so drain will clear itself.if it moves then you have no electrical control issues.It is probably bad diverter valve.Good luck hope this helps.

Posted on Apr 22, 2011

  • 195 Answers

SOURCE: I have a Am14 dishwasher that the water temp will

Hi Paul Dose it use the same cal-rod for both ?

Posted on Dec 14, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Water not filling.


r u using auto fill mode?if u r then try selecting high medium or low. check water pressure coming out of inlet hose, could b faulty valve not letting enough pressure thru.please reply if u need more help

Mar 14, 2010 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Fdb1050rec1 frigidaire dishwasher door leak


I think you most likely have a basin Float water level sensor that is no working correctly, the door seal is not water proof, if the water level gets over the lip of the basin it will leak on the floor.

May 01, 2017 | Frigidaire Dishwashers

1 Answer

Leaks badly


Most dish washers do not seal at the bottom, the door lip just sits
in front of the tub lip and does not make a real tight seal like a refrigerator door, so unless water is spraying out the top and sides of the door,I would assume that it is either overflowing,or you are using the wrong detergent and it is just foaming to much inside the washer and going over the lip and dripping on the floor. Once the suds stop getting agitated then turn back to water and don't look like suds.
So if you watch the washer during the cycle and the water s only coming from the bottom it is the water level switch inside on right
in the front,looks like a mushroom, once the washer reaches a certain level of water this switch floats up and shuts off the water to stop it from filling anymore. If this seems to be the case just remove the front bottom kick panel and you should be able to see the switch, watch it when the washer is filling,you can also push up on the little arm and the water should shut off. Post back with any questions.

Apr 16, 2009 | LG LDF6810ST Stainless Steel Built-in...

1 Answer

Water will not stay filled in tub on rinse cycle


It sounds like a siphon issue.
Check that the drain hose does a high loop before it goes into the drain pipe. (ie. drain hose loops above the water level inside the tub). Make sure the drain hose is not pushed too far down into the drain pipe. Also if the drain hose is sealed to the drain pipe this will create an airlock and a siphon will occur, allow air to enter between drain hose and drain pipe connection.
This should help you but if there is still a problem let me know and I'll try to assist you further.
Good luck!

Mar 21, 2009 | Maytag Washing Machines

2 Answers

Water level adjustment


You don't. Front load washers use only a very small amount of water. They fill a small amount, tumble a bit, resulting in water being absorbed into the clothes, which drops the water level in the tub. The washer senses this and adds more water, which repeats until water level stabilizes. The only way to get more water on wash cycles is to use delicate cycles, which use more water, resulting in a more gentle wash action. Remember that due to the low water consumption of front load washers, you should only use one tablespoon of HE detergent per cycle. (even less if you use 2x or 3x concentrate.) This is a FixYa solution. Your washer is working as designed.

Oct 23, 2008 | Whirlpool GHW9100L Front Load Washer

1 Answer

Door seal


switch off from mains
remove outer clamp holding door boot to cabinet and peel off door boot.
remove work top
there is a clamp holding door boot to tub. undo clamp and pull door boot away
lubricate slot in door boot that goes on to the lip of the tub using washing up fluid
starting at the top, insert lip of tub into slot in door boot. working both ways round, push door boot onto lip
fit outer clamp
push door boot on to lip of the cabinet and fit clamp.
test for leaks on a rinse cycle (water level is higher) water will be a bit foamy till washing up fluid is washed away
easy job but needs a bit of patience so go for it

Sep 07, 2008 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Hotpoint Aquarius WF440 Repalce Door Seal


no need to remove front panel
remove clamp that holds boot to cabinet and peel away boot
take top off
undo clamp that holds boot to tub and pull boot off
lubricate slot in new boot that goes on to lip of tub
starting at top, insert slot onto lip of tub and work your way round in both directions pushing slot onto lip
refit clamp
push door boot onto lip of cabinet and refit outer clamp
test on rinse cycle for leaks (water level is higher
water will be a bit foamy till fluid is washed away

Sep 06, 2008 | Hotpoint Aquarius WF000 Front Load Washer

2 Answers

Washer continuously fills but drains at the same time during rinse cycle.


you have the drain pipe too low into tthe house drain pipe, raise the washers drain pipe up , you only need four inches down into the hous drain

also the house drain pipe needs to be as high as the lid of the machine before you put the washer drain tube into the house drain

you have a syphoning effect

Apr 20, 2008 | Washing Machines

3 Answers

Agitator Not Working


check your motor coupler, lid switch

Nov 08, 2006 | Hotpoint VBXR1090D Top Load Washer

Not finding what you are looking for?
Hobart SR24C-4 Undercounter Dishwasher Logo

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Dishwashers Experts

Jason

Level 2 Expert

211 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

handygirl911
handygirl911

Level 2 Expert

59 Answers

Are you a Hobart Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...