Question about Computers & Internet
I purchased the Numark Mixtrack Quad and trying to map it over to Virtual DJ Pro. I downloaded the Mapping from the Numark Site and all mapped over correctly except my volume channels 1-4. on my board, the channels 1 & 2 are in the middle (left and right) while 3 & 4 are on the outsides. My issue is that my channels on the board are not match up with the channels on my computer. Channel 1 on my board (2nd slot) is the first volume channel on my computer. Channel 2 on my board (3rd slot) is showing in the 2nd slot on my computer. Numerically it all lines up, but physically they are all difference which makes it confusing when I am trying to play gigs. How do I correct this??
Posted by Anonymous on
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Here is the online programming tutorial:
Here is the full manual Should include Quick guide:
Here is FREE programming software for the PC:
Includes hardware info. You can buy programming cable at Radio Shack to connect to your PC.
Posted on Jan 04, 2008
I work at an authorized Denon service center and have repaired lots of Denon receivers including this model. So bare with me, and trust that I really do know what I am talking about.
The first thing you need to do is find out if those two speakers may be at fault. You can do it very easy by disconnecting them and connect two of the known good speakers into the channels that the bad sound is coming from and then connect the suspected bad speakers in where those good speakers were connected to.
If the same speakers still sound bad, you know that you have a couple of bad speakers. I think that it is likely that the speakers are OK, but it is a good idea to make sure.
If the sound from the suspected bad channels is now still bad with the two good speakers, you have an internal amplifier problem or you have a problem on the digital board.
For your sake, I hope it is the amplifier that is giving you this problem, if it is, that can be fixed by a good audio technician.
If the problem is the digital board, you may be in for some real headaches. Not that many audio techs are very good at troubleshooting a digital board, its not their fault, it is just a very difficult job.
In either case, it will need to be looked at by a qualified technician.
I hesitate to tell you this, but the problem sounds like a digital board problem. In some rare cases, a technician with excellent soldering skills can reflow a couple if the memory IC's on the digital board and restore proper operation. If the technician is top notch and isolates the problem to a specific IC on the digital board, they can replace that IC and you are good to go.
But in most cases, the technician will not even bother trying to troubleshoot the digital board because it can take hours of troubleshooting, and just order the board if it is available. Most of them are available from Denon, but they are very expensive. Normally the part alone is $200 to $300 and I have seen many times where it takes months to get it.
You can also send it directly to Denon's factory service center and that will get your unit back much quicker. They have direct access to the boards, where-as the authorized service center must order it thru one of the Denon parts distributors and they do not always have them in stock. so you end up waiting for a long time.
If you need to send it to the Denon factory service, let me know and I will email you a return authorization form, this must be faxed or emialed to Denon with the proper information and then they will fax or email it back to you with the RA number which must be written on the outside of the box before shipping it to them.
I hope that this information wasn't to overwhelming, but if you found it helpful a good rating would really be appreciated. It helps to keep the experts on FixYa motivated and willing to answer the questions people have even it the answer is not very good news.
I received an "inappropriate" rating from somebody who just wasn't happy with the truth, and most people never even bother to rate our answers. But that's another whole subject.
let me know if you need more help.
Posted on Jun 22, 2008
Had the same problem and fixed it today. It is the mute button. Whem you change from 1-2 to 3-4 if the mute button for 1-2 does not activate you will get the sound from 1-2 thru 3-4. Just change the setting and you are away. worked for me.
Posted on Nov 24, 2008
Tips for a great answer:
Feb 28, 2014 | Gemini DJ Gemini FIRSTMIX-PRO DJ...
Oct 24, 2013 | Numark Audio Players & Recorders
Aug 15, 2013 | Numark Industries Numark MixTrack Pro DJ...
Mar 01, 2012 | Numark Industries Numark MixTrack Pro DJ...
Apr 02, 2011 | Numark MixTrack DJ Software Controller
Mar 29, 2011 | Numark MixTrack DJ Software Controller
Mar 07, 2011 | Numark MixTrack DJ Software Controller
Mar 03, 2011 | Numark MixTrack DJ Software Controller
Feb 19, 2011 | Numark MixTrack DJ Software Controller
Mar 06, 2010 | Numark DJ/iO Sound Card
Jun 18, 2018 | GE Computers & Internet
43 people viewed this question
Usually answered in minutes!