Question about Kenwood KAC-9152D Car Audio Amplifier

1 Answer

HAVE A KENWOOD AMP MODEL KAC-9102D . iT KEEPS SHUTTING OFF WHEN i TURN THE RADIO LOUD. ANY SUGGESTIONS

I HAVE A KENWOOD AMP MODEL KAC-9102D . iT KEEPS SHUTTING OFF WHEN i TURN THE RADIO LOUD. ANY SUGGESTIONS

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 79 Answers

Either bad ohm load or over heat if the ohs on the speaker wires to the amp are lower than specified use in the manual it will act funny cause it is pusing harder than its meant to and if it gets too hot either bad location or bad amp you can try turning the gain down a little until the amp stays on constantly at high volume

Posted on May 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Kenwood amp shuts down and goes into protection mode after I play it for a minute or so. I have it cranked pretty loud. I have checked out my speakers and there are no shorts. I have a preamp between my...


could be you don't have enough voltage going into the amp or it could be the pre amp in between. if your voltage is below 11 volts then you need more voltage. you should have at least 12 to 14.4 volts.or you might have a small short in your amp.

Aug 03, 2010 | Kenwood KAC-9102D Car Audio Amplifier

1 Answer

To bridge a Kenwood KAC-9102D


Hello laurogleal,

The Kenwood KAC-9102D is a mono amp. There is no bridging. Having two sets of terminals is just a more convenient way of connecting two subwoofers. The amp is stable down to 2 ohms impedance, so it is safe to run 2 4 ohm loads in parallel.

Hope this helps.

Apr 28, 2009 | Kenwood KAC-9102D Car Audio Amplifier

2 Answers

1 amp cuts off


i had this same prob. & i run 2 amps as well, cameto find out i had a neg. & positive touching , so check all ur wiring for tht amp..

Apr 01, 2009 | Kenwood KAC-9102D Car Audio Amplifier

1 Answer

Install my Kenwood KAC-9102D in my 2006 Acura RSX Type S


You will probably need to use a Line Output Converter (LOC). They're available at virtually any shop that sells car audio.

Many times, the outputs of the OEM amplifier will have significant DC voltage on them. This could damage the input circuits on the kenwood amplifier.

Let me know if you have any other questions.

Aug 24, 2008 | Kenwood KAC-9102D Car Audio Amplifier

1 Answer

How to install kenwood kac-9102d in 2006 acura rsx


My recommendation is to get a line level converter. Go to a car audio shop or even best buy and specifically ask for a line level converter. It will have speaker wires in and RCAs out. Connect the speaker wires to the sub woofer speaker wires and then you will have the RCAs to run to your amp. I hope this helped.
-Andrew Hawkins

Aug 24, 2008 | Kenwood Car Audio & Video

1 Answer

Doesn't turn on


You need to confirm that the B+ voltage isn't dropping at the amp.

With your multimeter set to DC volts, the black meter lead on the ground terminal of the amp (not on the point where the ground wire connected to the vehicle) and the head unit on (so the amp will have remote voltage applied), touch the red lead alternately to the B+ and remote terminals of the amp. If the voltage is below ~11 volts, you need to check the wiring feeding whichever line is too low.

May 21, 2008 | Kenwood KAC-9102D Car Audio Amplifier

1 Answer

Will it work together


put a the amp the max charge permitted, and y you have a preamp you can makeit work.

Feb 10, 2007 | Kenwood KAC-9102D Car Audio Amplifier

1 Answer

Amp keeps overheating


Try to turn down the volume??? LOL No really most likly the voice coil is overheating on the speaker, or the unit is over heating. Try to add a fan on top of the unit as I found this on high powered units, that they are being push hard and getting hot. Is the amp really hot when it does this? If it is then its a normal thing as not enough venilation. if its not hot then theres a problem in the amp and should be bench checked by a pro with load resistors and a tone generatoe as well as a scope to check if theres a clipping problem in the output stage.

Sep 02, 2006 | Kenwood KAC-9102D Car Audio Amplifier

Not finding what you are looking for?
Kenwood KAC-9152D Car Audio Amplifier Logo

Related Topics:

273 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4874 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...