Question about GE Monogram ZISS480DRSS Stainless Steel

1 Answer

Hello. My G.E. Monogram water dispenser trickles water after we get water from it. We have to keep a cup there to catch the excess water. How do I fix it so it stops as soon as we get water out of t

It is a side by side built in model with the condenser on top in a fold up door.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Try replacing the Water Valve. It is located in the back of the refrigerater, left side. You should see three tubes connected to it. This part fixes the following symptoms - Leaking water, Water dispenser will not dispense water, Ice maker will not make ice and Ice maker won't dispense ice. GE part#WR57X10032. The Water Valve is extreemly easy to replace. Only takes about 15 mins total time to remove, install and confirm. I just replaced mines..my problem went from leaking water to no water was dispensing at all. I have the GE Profile, it uses the same water valve as your GE Monogram. There is a You Tub video that also shows how to replace. Good Luck!

Posted on Dec 28, 2013

  • Bonita
    Bonita Dec 28, 2013

    Meant You Tube..!

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

aborcass
  • 2651 Answers

SOURCE: how to unlock control lock on ge monogram side by side

shoud be amatter of pressing abutton and holding in for 3-5 secs to unlock. look closely at the control panel it should indicate which button(s)

Posted on Jan 25, 2009

  • 13 Answers

SOURCE: GE Monogram ZISS480DMCS Ice Maker Problem

i would first check water supply to ref. measure the resistance of coil either open or resistance. if all this is ok then exit side of line needs to be checked for water.

Posted on May 03, 2009

  • 13 Answers

SOURCE: Monogram water flow problem

common low flow is a kinked line or a bad water valve, the solioid valve has a filter that may be dirty. then go from there

Posted on May 03, 2009

VtToolMan
  • 704 Answers

SOURCE: 42'' monogram getting very hot between doors and in unit above

This is typical for frost-free refridgerators/freezers. In order to keep ice from buiding up on the interior walls of the freezer section, the manufacturer installs electric defrosting elements and extra "warming" elements in the outer edges of the cabinet, normally around the door openings to help mitigate any frost/ice build up and surface condensation that typically occurs on the exterior surfaces as the doors are opened and closed frequently.

These edge warmers stay very warm to keep ice and condensation from accumulating and will become VERY very warm (hot) when the fridge/freezer is in the once a day defrost cycle.

Unless you have an energy saver switch (GE trademark) inside the fridge section, which you can turn off, there is no way to disable these added elements. If you find that you're getting ice building up in the freezer, you'll need to turn off the energy saver switch to resolve that issue.

Energy Saver switch "ON" means these elements are off, while having the ES switch "OFF" means those heaters are running all the time and costing you more in energy consumption

Posted on Jul 13, 2009

  • 1 Answer

SOURCE: GE Monogram will not accept freezer/fridge

My ge monogram gets warm every year this time of year. All of a sudden no ice and everything defrosts. We vacuumed vents up top last yr and it got cold again. What the heck???

Posted on Aug 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does a lot of detergent remain in the soap dispenser after a washing cycle is complete


Was the dispenser cup wet when you added detergent?
Make sure the dispenser cup is dry before adding powdered detergent. If dispenser cup is wet, the detergent can clump.
Is the cycle incomplete?
If the previous cycle did not complete, the detergent can become caked in the dispenser cup if it is left sitting in the dishwasher.
Is the detergent old?
Older detergent exposed to air will clump and not dissolve well, which will cause the dispenser door to stick to the detergent. Replace detergent if necessary and store the detergent in a tightly closed container in a cool dry place.
Is the water temperature too low?
For best washing and drying results, water should be 120oF (49o C) as it enters the dishwasher.
Were items blocking the dispenser that kept it from opening?
Items blocking the detergent dispenser will keep it from opening. Make sure water action can reach the dispenser.
Detergent guidelines
  • Use automatic dishwashing detergent only.
  • Other detergents can produce excessive suds that can overflow out of the dishwasher and reduce washing performance.
  • Store tightly closed detergent in a cool, dry place.
  • Fresh automatic dishwasher detergent results in better cleaning.
  • Add detergents just before starting the cycle.
  • The amount of detergent to use depends on the hardness of your water and the type of detergent.
  • If you use too little, dishes won't be clean.
  • If you use too much in soft water, glassware will etch.
  • Suggested fill amounts are for standard powdered detergent. Amounts may vary if you use liquid or concentrated powdered detergent. Follow instructions on the package when using these detergents.
  • Water hardness can change over a period of time. Find out your water's hardness by asking your local water department, water softener company, or county extension agent.

Nov 25, 2010 | LG Washing Machines

2 Answers

GE Monogram fridge is not dispensing water. Ice maker is working fine. Not a water filter issue. thanks -


Water and ice solenoid valve is one valve with two coils and exits.
The most posible case is the water side is coggled or coil broken and need to bee clean or a new valve

Oct 16, 2010 | GE Monogram ZISS420NRSS 42" Built-In...

1 Answer

Manually add water?


Put 2 cups of water into the maker.

Jun 20, 2010 | GE Monogram ZDI15C Automatic Icemaker

1 Answer

Water dispenser not working. The ice dispenser will work but the water will not. I held it down for 2 minutes to be sure there was no water in the line but its still not working. We also changed the filter...


Check in the back wall of the refrigerator section and confirm the water dispenser reservoir is not frozen.

Listen for the solenoid valve to click when actuating the water dispenser. If no click check the solenoid valve.

The wires for the switch are in the door hinge of the freezer. Confirm that they have not failed.

Hope this is a helps?

Jun 18, 2017 | GE Monogram Side by Side Refrigerator

1 Answer

Water dispenser drip


Use a cup instead of a paper towel. Empty as needed.

Jul 14, 2009 | KitchenAid Superba Architect KSCS25INSS...

1 Answer

Water keeps dripping after it dispenses water thru the door


When you push the button, the CLICK you hear when the water flows is the Water delivery solenoid opening to let water thru, then snapping shut when U R done. The Spring is weak (prob wrong type, size, strength at factory) or the valve seal is cracked, torn, hardened or crushed.

Since all this is inside the door, you will either have to take it apart to see/fix/replace.

Quick fix: turn down the water pressure coming in(?)

Call Mr. Handyman to fix.

If under warranty - they might fix this for you for free
If this is a factory defect, there might be a recall in place for repair/replacement parts

Googlee both - Make/Model + Dripping Valve + Recall
Good Luck!

Jan 17, 2009 | Frigidaire FRS3R5EMB Side by Side...

1 Answer

One dispense spigot barely trickles


You need to take a paper clip and clean the little holes where the water comes out on the left side (It's like a screen). Also you should pull the silver thing that adjusts to allow taller cups underneath up and down several times. You should do the latter every week. It helps get rid of some of the coffee grounds that block the aforementioned little holes.

Oct 05, 2008 | Jura Capresso Impressa E8 Espresso/Coffee...

1 Answer

Leaks at the hot water spout during coffee brew


I had the same problem. I ended up taking the coffee machine apart and found that the reason coffee trickles out around the hot water spout is that the two coffee nozzles were partially plugged. Since I Had parts of the coffee machine apart I was able to clean it easily. It may also be possible to clean the assembly using a pick of some sort and clean out the holes of the two normal coffee spouts. Inside it is just a open cavity so gentle poking around and using some steaming hot water may do the trick.
If you want to take the machine apart you need to do the following: 1) take of the warmer plate on the top - 2 storz screws but an allen key works as well 2) take off the top plate of the machine - another 4 or 5 screws - make sure you empty the beans first otherwise you will have a mess 3) remove one screw from the right hand side of the removable coffee ground tray. Once this screw is removed the front panel is free to swing open except for the pipes connecting the front 4) unclip the steam assembly - there are a couple of plastic catches on the top. this will free the steam assembly from the front panel and also free a pipe connections. The steam dispenser pipe will also come free from the steam assembly. 5) remove the coffee pipes from the up and down sliding coffee dispenser. This is a small whitish color clip with 2 pipes connecting into it. The white clip has a little plastic catch on the top that frees it. The front panel should now swing open freely. 6) remove the sliding coffee dispenser from the front door. There are 4 plastic catches, 2 on either side. the whole front sliding coffee displenser now comes free 7) Take the sliding dispenser apart by release the 4 plastic catches on the front curved planel. 8) Inside the sliding dispenser is a white plastic piece that connected to the piping released in step 5. There is a small plastic catch that needs to be pressed while pulling fairly hard on the plastic piece and bending the whole piece. 9) You will now see the plugged spouts. It goes back together really easily.

Aug 13, 2008 | Jura Capresso Impressa S8 Coffee Maker,...

1 Answer

Monogram water flow problem


common low flow is a kinked line or a bad water valve, the solioid valve has a filter that may be dirty. then go from there

Jun 11, 2008 | GE Monogram ZISS480DRSS Stainless Steel

Not finding what you are looking for?
GE Monogram ZISS480DRSS Stainless Steel Logo

233 people viewed this question

Ask a Question

Usually answered in minutes!

Top Refrigerators Experts

KJ4QOB

Level 2 Expert

55 Answers

Jim Akins

Level 2 Expert

82 Answers

rodney bartholomew

Level 1 Expert

11 Answers

Are you a Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...