Question about Emerson EWF2704 TV

Open Question

Need to set video mode without a remote or through dish network remote

We have long lost our factory remote control and have a dish network all in one remote control. I need to set tv to video mode through the tv or dish remote

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: Remote code for Emerson SLC195EM82 TV

Here is a list of remote codes for Emerson TV: 004 009 014 023 024 025 026 027 030 032 033 034 035 036 037 038 039 040 041 042 043 045 046 049 053 116 135 147 177 179
Give them each a try (a pain I know) and please rate me if they work!
Take Care,
-WN

Posted on May 06, 2008

Ad
  • 15 Answers

SOURCE: How to get TV/video mode without remote

some tv do that changing the channels.

in the control panels in the tv where r the buttons for change channel there must be video button, push it and there you go.

Good Luck

Posted on Jan 12, 2009

  • 5 Answers

SOURCE: video mode

my TV remote broked and i want to know how can i change Emerson EWF2004to video without the remote so i can watch movies

Posted on Feb 07, 2009

freetek
  • 5568 Answers

SOURCE: Remote control code for dish network for Emerson

Your Dish remote was probably designed years before the Emerson set and may never have codes for it.
However, you can try the followng brands from the Dish code list to see if you can get some basic functionality:
Funai, Symphonic, Sylvania, Aventura, Durabrand, ESA, Magnavox, INSIGNIA, Philips and Misakai

All of the above are manufactured by Funai - the least and lowest of the Japanese electronics firms.

Posted on Sep 07, 2009

barbu51
  • 566 Answers

SOURCE: I have lost my remote how do i get the tv on video

Try to go below channel 2 or above 125, sometimes that is where you will find the video input. Hope this will help

Please do not rate this answer(unless it helps)as it is only a suggestion.

Posted on Dec 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to Set Up the Kbox Pro Digy (FTA Receiver)?


-Extract files (factory bin & version bin)
http://www.abadss.com/forum/983-kbox...te-v2-0-a.html
-from remote, menu-config-system recovery & select delete all channels then factory reset
-insert USB into port in front of reciever, menu-utilities-data transfer-data download (from USB storage)-factory bin (version 1.81)
-menu-config,system recover y and select factory reset
-menu-utilities. data transfer, data download from usb storage-select latest bin (version 2.18)
-menu-config-system recovery-factory reset
-plug khub into reciever using black serial cable, also plug into network cable running to your router or switch
-from controller-menu-utilities-data transfer-data download from USB storage, then select khub activation
-menu-installation-options and make sure all AU options are set off and mode is set to network
-menu-installation-dish settings & config satellites you have setup dishes, then press red button on each satellite to scan in channels
-menu-config-network and change mode to DHCP press green button on remote and wait for it to be complete
-once previous step is complete, turn reciever off with remote, then from back. Wait 30 seconds, turn unit back on

Oct 20, 2016 | Video Game Consoles & Games

1 Answer

I have lost my dish set remote so how i can change the channels on the tv.i have tv remote.


if you lost your remote control for the dish simple call the customer service and asked for a new remote control. there are no ways to program a regular remote to a dish receiver box.

Feb 07, 2014 | DISH Network Televison & Video

1 Answer

I have lost the code book. I know how to program it but have no ideas what the code is. The TV is a Sanyo and we have Dish Network for satellite. Any help would be appreciated.


In order to program the remote to a TV set, hold the clear "TV" button in the upper left hand corner four four seconds or until all four of the mode buttons light. Next press in one of the three digit codes below followed by pound (#) Remote codes: 590, 683, 720, 591, 543, 593, 813, 542, 533, 652, 726, 611, 500, 503, 627, 661, 956, 591, 694, 666, 252 After trying each code press the volume and power buttons, if they control your TV set be sure to press the "SAT" button.
Daniel Busa
DISH Network
Customer Service

Aug 28, 2011 | Philips SRU2103S-27 Remote Control

1 Answer

How do i change tv 2 with reciever or remote 1, lost remote 2.


Hi this isMike Houston of DISH Network and I see you have lost your TV2 remote. Until youget your 2nd remote you can put the receiver in Single Mode and putTV1 on the channel you want to watch for TV2 and then put it back in Dual Mode.I can help you in getting your TV2 remote so you can watch TV on both setswithout having to change the Mode setting on TV1, I will send you my e-mail andyou can contact me through there; michael.houston@dishnetwork.com.

Aug 08, 2011 | DISH Network DVR-625 DTV Receiver /...

1 Answer

I have a AVEX URC-R6 Remote controller that was working fine for almost 3 years with a DISH 722 Reciever/DVR. One morning the receiver IR would receive no signals from either the AVEX remote, or the...


trwck

I have provided instructions on how to save setting on the receiver and remote plus instructions for learning mode. I hope this helps.

Ray Calo
DISH Network

Back Up Remote/Receiver Data
  • Receiver: 222k and 722k
    1. Verify that the customer has an unobstructed LOS and is within 10 feet of the receiver. The customer will need to direct the remote toward the receiver for the duration of the System Wizard setup.
    2. Press and hold the number 0 until the pop-up 380 appears on the screen.
    3. Verify that the System Wizard says the remote is configured correctly.
    4. Select Advanced on the screen.
    5. Select "Backup My Settings Now".
    6. Verify that the purple gem is displayed beside the correct selection.
    7. Select Next.
    8. Select the type of backup to be performed:
      • Full system backup
      • Back up receiver settings
      • Back up remote settings
    9. Verify that the purple gem is displayed beside the correct selection.
    10. Select Continue twice to initiate data transfer. Maintain unobstructed LOS while the green progress bar fills.
    11. Select Continue to resume programming.
  • Restore Receiver Data
  • Receiver: 222k and 722k
    1. Verify that the customer has an unobstructed LOS and is within 10 feet of the receiver. The customer will need to direct the remote toward the receiver for the duration of the System Wizard setup.
    2. Press and hold the number 0 until the pop-up 380 appears on the screen.
    3. Verify that the System Wizard says the remote is configured correctly.
    4. Select Restore on the screen.
    5. Maintain unobstructed LOS while the green progress bar fills.
    6. Select Continue to resume programming.
  • Teach Learning Commands
  • Receivers: 222k and 722k
    1. Ensure the DISH Network remote control is programmed to the desired remote address to operate the DISH Receiver.
    2. Place both the DISH Network remote and the original equipment's remote control on a flat, stable surface.
    3. On the DISH Network remote, press and hold the mode button for your equipment for about three seconds until all of the mode buttons light up, and then release it. Your selected mode button will blink.
    4. Select the type of learning you wish to perform:
      • Hybrid Mode
        1. Press and release RECALL, then hold the RECORD button for about three seconds until the mode button is lit again. The button remains lit while learning.
        2. Point the front of the original equipment's remote to face the small square (IR window) on the front left-hand side of DISH's remote. Remotes must be within 4 inches of each other.
        3. On the DISH Network remote, press the button you want to teach.
        4. On the original equipment's remote control, press and hold the button you want learned. If the DISH Network remote learns the command, the mode light blinks off and then back on. If the mode light blinks three times or remains lit, the DISH Network remote did not learn the command. You may need to press the button on the original remote several times for the DISH Network remote to learn the command.
        5. After a button has learned a command successfully, repeat steps 3 and 4 until all commands you want have been learned.
        6. To end the learning sequence:
          • Press one of the mode buttons on the DISH Network remote. This saves all of the commands for that mode and exits learning to return to normal remote control operation.
      • Normal Mode
        1. Press and hold the RECORD button for about three seconds until the mode button is lit. The button remains lit while learning.
        2. Point the front of the original equipment's remote to face the small square (IR window) on the front left-hand side of DISH's remote. Remotes must be within 4 inches of each other.
        3. On the DISH Network remote, press the button you want to teach.
        4. On the original equipment's remote control, press and hold the button you want learned. If the DISH Network remote learns the command, the mode light blinks off and then back on. If the mode light blinks three times or remains lit, the DISH Network remote did not learn the command. You may need to press the button on the original remote several times for the DISH Network remote to learn the command.
        5. After a button has learned a command successfully, repeat steps 3 and 4 until all commands you want have been learned.
        6. To end the learning sequence:
          • Press one of the mode buttons on the DISH Network remote. This saves all of the commands for that mode and exits learning to return to normal remote control operation.
  • Mar 25, 2011 | DISH Network ViP722 DTV Receiver /...

    1 Answer

    Dish Network IR Remote's SAT Mode Not Working ________________________________________ I programmed my Dish Network Remote (IR 1.5 Blue Button Remote Control ) for my Sharp 27F543 and now the remote would...


    Hello, this is Nick Franta with DISH.

    If you are trying to get the remote programmed to the receiver you can remove the smartcard from the receiver and that will prompt the system info screen. This will allow you to program the remote to the receiver.

    If you need the process for programming the remote, here it is:
    1. Go to System Info screen (in this case -- obtain by removing smartcard from receiver)
    2. Hold down the SAT button until all mode lights light up.
    3. Enter a number between 1 and 15 using the numeric keypad on the remote.
    4. Press the pound (#) button
    5. Once the SAT button blinks three times, press record.
    Hope this helps!

    Jan 01, 2011 | DISH Network IR Remote Control

    1 Answer

    I have a bell express view 6100 but the remote does not work. It appears that I should be on frequency 1 but my receiver is set to frequency 11. Is there a way I can reset the receiver to the original...


    We would be happy to help you with that. We would recommend programming your DISH remote to the remote address your receiver is set to. First access "SystemInfo" at TV1, this can be done by pressing the menu button on the front of your receiver. Using the remote that is NOT functioning, pressand hold the "SAT" button until all the mode buttons at the top of the remote light up. On the number pad, enter the remote address we want, in your case this would be "11", press the pound (#) button, then finally press the record button 3 times. After re-addressing the remote you should be able to use the remote to exit the menus. We hope these steps get your remote working. Thanks for being a valued DISH Network customer!


    Phillip Chang
    DISH Network Customer Service Representative

    Nov 03, 2010 | DISH Network IR Remote Control

    1 Answer

    Programme remote to work with sony tv


    To program your DISH Network remote to your Sony TV you will simply- press and hold the TV Mode button until all the other mode button back lights illuminate, then release.

    -Now while the TV mode button is blinking please enter in the remote code 500 which is the remote code for your Sony TV after entering 500 then press the pound (#) key.

    -After pressing the # key on the DISH Network remote, the TV mode button should blink 3 times and then turn off completely. This will mean the programming of the DISH remote to your TV has been completed successfully. While still in TV mode try any of the functions on the remote, such as turning the volume up or down on your TV or attempting to press the power button.

    -The DISH Network remote should now be programmed to control your TV.

    -If the remote code 500 doesn't program the DISH Network remote successfully you can also try each of the following using the same procedures, 000, 590, 640, 502, 002, or 567.

    I hope this resolved the issue for you! Please feel free to contact us if you need any additional assistance.
    -Kirstie DISH Network

    Sep 16, 2010 | DISH Network IR Remote Control

    1 Answer

    I have a dish network remote control that I am trying to use to get to my video 1 or video 2 channels on my Sylvania 6420FF tv. The Sylvania remote is dead to the world and I need the Dish remote to get to...


    You will need to by a universal remote in most circumstances as the Dish remote may not cycle through the inputs on your tv. You can try the recovery button on the remote it will have a small R on it. Press it many times to se if it it set to cycle through the inputs. Thanks for using Fix Ya.

    Aug 01, 2009 | DISH Network 118216 Remote Control

    3 Answers

    I lost the remote for the ilo tv and need to get it to video 2 mode in order to play ps3. I can turn the tv on and off and change channels with dish network remote but cannot get to video 2. The "input" or...


    Please follow the steps below to program your remote control to equipment other then your DISH receiver:
    Note: If you start this procedure and at any time and do not press a button within 20 seconds, the remote will end the procedure automatically. Simply start over again. Use the TV button for your TV, the VCR button for your VCR or DVD player. These Mode buttons are located at the top of your remote control.
    1. With the desired equipment on, press and hold the correct Mode button until all mode button backlights illuminate, then release. 
    2. Press the numbers 5-0-0 on the remote control. 
    3. Press the Pound (#) button on the remote. 
    4. Press and hold the correct Mode button until all mode button backlights illuminate, then release. 
    5. Press and release the Power button on the remote control. 
    6. Press the Up button once a second while pointing the remote at the desired equipment. If the code for the equipment comes up, the equipment will power off. 
    7. Press the Pound (#) button. If the code entered is valid for the remote, the mode light flashes three times. 
    8. To verify the code works try several different functions for that equipment. 
    lone99star

    Jan 09, 2009 | iLO 2600 Television

    Not finding what you are looking for?
    Emerson EWF2704 TV Logo

    Related Topics:

    125 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Emerson Televison & Video Experts

    The Knight
    The Knight

    Level 3 Expert

    75276 Answers

    matt martin
    matt martin

    Level 3 Expert

    1216 Answers

     Grubhead
    Grubhead

    Level 3 Expert

    5384 Answers

    Are you an Emerson Televison and Video Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...