Question about Kenwood KDC-7007

1 Answer

I am trying to install a deck in my car. I hooked up all the wires and the deck (kenwood kdc-7007 worked at the store we bought it. There is power coming from the red wire in the car but doesn't power the deck. Could you please tell me how to wire it so that it will turn on? Do I need to hook up the blue wires too? I have no blue wire coming out of the car.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Did u check the fuse in the back of the radio?did you check the radio fuse in your car? Do you have the yellow battery memory wire hooked up? Is the black ground wire connected

Posted on May 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Subs make one very loud bang when car starts i have a kenwood kdc 528 deck and 2 pioneer 12in subs an amp


Hook it up properly to the deck remote on wire ,(Dude) End stay off the (Drugs)

Nov 22, 2012 | Pioneer Car Audio & Video

1 Answer

Kenwood KDC-319 CD Player Logo Problem with KDC-319 CD Player installed a kenwood kdc 319 in a 04 chevy malibu when i have car off i turn deck on an my cars dash board lights turn on Posted by A


I would start by disconnecting the radio and hooking it up right,the power should go through the ignition switch.So that when you turn the car off the radio will go off and to hear it on again you have to turn the key to accessory or start it.That might take care of a few of your problems.

Jun 25, 2012 | Kenwood KDC-319 CD Player

1 Answer

Installing Kenwood KDC-MP345U into a travel trailer. Trailer is pre-wired for deck. Have Orange (hot) & White (ground) from trailer converter to deck. Hooked up yellow (battery) wire from harness to...


the power terminals from the trailer arent direct connected to the battery terminals.when you are plugged to the mains the battery is charging and disconnect [via a relay perhaps]the orange terminal from batt+.try to make anew connection from the trailers battery terminals with a new fuse separated from all trailers circuit'use 2-2.5 mm*cables and a 15amps fuse.connect the yellow and red to+batt and black to- batt.

Jun 05, 2010 | Kenwood Car Audio & Video

1 Answer

Radio only owkrs with amp hooked up


Amp ic is out or there is an open signal ground in the receiver.

Mar 28, 2010 | Kenwood KDC-7007

1 Answer

I'm trying to install my new kenwood kdc-mp642u cd deck but i can't get it to power on in my car


find a wire that is constent hot hook it to the yellow and find an ignition on hot and then hook it to the red and hook up the ground u might need a test light u can get them at an auto parts store or at walmart for about 5.00 or less

Oct 06, 2009 | Kenwood KDC-MP642U

1 Answer

I just bought a Kenwood KDC-MP438U I installed all the wires right, power is to the deck because it accepts a cd. the deck face doesn't light up. I called in at Kenwood and they had me test it directly to...


Check your Ground Wire inside the Truck and Check the Illumination Wire. I Think on Kenwood the Illumination Wire goes with the Power Wire. If they still will not work, You might want to get a Wiring Harness from Schoche.com Please Rate My Response! Thanks!

Jan 30, 2009 | Kenwood KDC-MP438U Car CD/ MP3 Player

1 Answer

Kenwood deck reads protect and won't function


you have one of your speaker wires shorted out to the body of the car somewhere, or the speakers that you installed are bad. That is the only two reasons it will go into protect. Correct the problem, then reset the deck - it should work fine.
Kenwood builds this feature in to protect the outputs - so they dont burn up in the case of shorted speakers or wiring.

Jan 16, 2009 | Kenwood KDC-MP235 CD Player

1 Answer

Kenwood kdc-7007


Your owners manual or the web site for Kenwood or try www.radio-code.com to get the factory code and the proceedure for inputting it into you radio. Good luck.

Apr 23, 2008 | Kenwood KDC-7007

Not finding what you are looking for?
Kenwood KDC-7007 Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4869 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...