Question about Washing Machines

1 Answer

How to raise and lower the pedestals

Wm2233hs

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 236 Answers

If you are referring to the adjustable height feet under the machine I would suggest what is called a Headset Spanner for bicycles. The space under the washing machine at its lowest height is very limited, only a few millimetres. The Headset spanner is very thin and can access the adjusting nuts at this height. These spanners are about eight pounds from Halfords and usually have four different nut sizes on each spanner, two at each end. If you can borrow a head spanner so much the better. These spanners are used to tighten the large nuts that hold the handlebars (headset) to the frame of the bike.

Posted on Dec 26, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just purchased a LG 8500HSA Mega Front Load Washer Special Order! What is the Pedestal Model Number?


Please check your model number. 8500HSA does not cross to anything on LG.COM.

Universal pedestals are for sale at Sears, Home Depot, Lowers, and Best Buy. The pedestal and machine will bolt together, that is, a bolt will run upward from the pedestal into threaded bolt holes in the bottom of the washer. If you can measure the distance from bolt hole to bolt hole on the bottom of the washer, you can check to see if the universal pedestal fits before you buy it.

Several months ago I took my front loaders off the pedestals. The pedestals were kind of nice for handling the clothes but about 40% of the time I spilled either detergent, bleach, or softener because the pedestal put the drawer too high for me.

Apr 18, 2015 | LG Washing Machines

2 Answers

My kitchen aid stand mixer startnig making noise and wobbling. I noticed that the pin attaching the top to the base has been pushed out halfway and I can't push it back. Any solutions?


Remove the bowl, turn it upside down on a towel, look up inside the pedestal. Right in the middle where the hinge pin goes through there is a screw, unscrew it a little, push the hinge pin back to where it belongs and then tighten the screw up tight. Turn mixer up the right way, raise head up, fit bowl & flat paddle. Lower head & turn machine on low, listen for paddle tinging on bowl, if it is touching turn off and raise the head. Look into hinge area from the front, that screw is the head height adjustment. Clockwise to lower paddle in bowl, anti clockwise to raise. You want to lower it until you hear the paddle tinging on the bowl & then raise it enough to clear without tinging. You don't wind the screw in & out huge amounts, 1/4 to 1/2 a turn at a time is plenty.

Dec 14, 2014 | KitchenAid KITCHEN AID 5 Quart Artisan...

1 Answer

How do i adjust the bowl height on an ksmc5os?


I'm not familiar with your model but on stand mixers with crank handle bowl lift there are 2 places for it to be. With bowl lift down there can be s screw straight in from the front on the pedestal just above the bowl lift sliding bracket, the full range of adjustment is half a turn, anti clockwise to raise, clockwise to lower. The other one is a small screw sticking down from under the gear case where the bracket that carries trhe bowl slides up and down. Clockwise to lower, anti clockwise to raise.

Aug 19, 2014 | KitchenAid KSMC50S Commercial Stand Mixer

1 Answer

How to replace crankpully on 3300 olbs


The harmonic balancer on these engines is now press fit onto the crankshaft and requires the use of Tool J-38197 for removal. The torque specification to be used during installation has also been revised. The procedure to be used when replacing the crank sensor is as follows:

REMOVAL






  1. Disconnect serpentine belt from crankshaft pulley.


  2. Raise vehicle on hoist.


  3. Remove right front tire and wheel assembly.


  4. Remove right inner fender access cover.


  5. Using 28 mm socket, remove crankshaft harmonic balancer retaining bolt.


  6. Remove crankshaft harmonic balancer using Tool (J-38197).


  7. Remove foreign object deflector (DO NOT use pry bar).


  8. Disconnect sensor electrical connector.


  9. Remove sensor and pedestal from block face.


  10. Remove sensor from pedestal




INSTALLATION






  1. Loosely install crankshaft sensor on pedestal.


  2. Position sensor with pedestal attached on Tool J-37089.


  3. Position tool on crankshaft.


  4. Install bolts to hold pedestal to block face, torque to (18-26 lb. ft.).


  5. Torque pedestal pinch bolt to (26-44 lbs. in.).


  6. Remove Tool J-37089.


  7. Install foreign object deflector.


  8. Place Tool J-37089 on harmonic balancer and turn. If any vane of the harmonic balancer touches the tool, replace the balancer assembly.


  9. Install balancer on crankshaft.


  10. Apply thread sealer GM #(NNN) NNN-NNNNor equivalent to threads of crankshaft balancer bolt. Torque bolt to + 56 degrees (104 lb. ft. + 56 degrees).


  11. Install inner fender shield.


  12. Install tire and wheel assembly. Torque lug nuts to (104 lb. ft.).


  13. Lower vehicle.


  14. Install serpentine belt.
see this vedio

Jul 11, 2014 | 1993 Oldsmobile Cutlass Ciera

1 Answer

How do you lower the height on a LG washer and pedestal? It's too high by 1" to fit under my wall cabinets.


The pedistal has 4 leveling legs on the bottom of it you can adjust to a certain point. You may have to take the lefts off completely and if it still doesn't fit, you unfortunately didn't measure properly.

Mar 16, 2013 | LG WDP4W 14 inch Pedestal White

1 Answer

I need to replace crank shaft timing sensor


  1. Disconnect the negative battery cable.
  2. Disconnect the electrical connector at the sensor.
  3. Using a 28mm socket and pull handle, rotate the harmonic balancer until any window in the interrupter is aligned with the crank sensor.
  4. Loosen the pinch bolt on the sensor pedestal until the sensor is free to slide.
  5. Remove the pedestal to the engine mounting bolts.
  6. While manipulating the sensor within the pedestal, carefully remove the sensor and pedestal as a unit. To install:
  7. Loosen the pinch bolt on the new sensor pedestal until the sensor is free to slide.
  8. Verify that the window in the interrupter is still in the correct place.
  9. Install the sensor and pedestal as a unit while making sure that the interrupter ring is aligned within the proper slot.
  10. Install the pedestal and tighten the engine mounting bolts to 22 ft. lbs. (30 Nm).
3X Sensor
  1. Disconnect the negative battery cable.
  2. Remove the sensor harness connection to the sensor. Fig. 1: Unsecure the harness, then unfasten the bolt to remove the CKP sensor 86815102.gif

  3. Unsecure the sensor block bolt.
  4. Remove the Crankshaft Position (CKP) sensor from the vehicle. Inspect the O-ring for cracks and replace if needed. To install:
  5. Install the new O-ring if needed and lubricate with engine oil.
  6. Install the sensor into the hole in the block.
  7. Install the mounting screw and tighten to 71-88 inch lbs. (8-10 Nm).
  8. Attach the sensor harness connector, then connect the negative battery cable.
Dual Crank Sensor Sections 3 and 4 of this manual also cover testing, removal and installation, and adjustment of many computer controlled components.
  1. Disconnect the negative battery cable.
  2. Remove the belt(s) from the crankshaft pulley.
  3. Raise and support the vehicle safely.
  4. Remove the right front wheel and inner fender access cover.
  5. Remove the crankshaft harmonic balancer retaining bolt, then remove the harmonic balancer.
  6. Disconnect the sensor electrical connector.
  7. Remove the sensor and pedestal from the engine block, then separate the sensor from the pedestal. To install:
  8. Loosely install the crankshaft sensor to the pedestal.
  9. Using tool J-37089 or equivalent, position the sensor with the pedestal attached, on the crankshaft.
  10. Install the pedestal-to-block retaining bolts. Tighten to 14-28 ft. lbs. (20-40 Nm).
  11. Tighten the pedestal pinch bolt 30-35 inch lbs. (3-4 Nm).
  12. Remove tool J-37089 or equivalent.
  13. Place tool J-37089 or equivalent, on the harmonic balancer and turn. If any vane of the harmonic balancer touches the tool, replace the balancer assembly. NOTE: A clearance of 0.025 in. (0.635mm) is required on either side of the interrupter ring. Be certain to obtain the correct clearance. Failure to do so will damage the sensor. A misadjusted sensor of bent interrupter ring could cause rubbing of the sensor, resulting in potential driveability problems, such as rough idle, poor performance, or a no-start condition.
  14. Install the balancer on the crankshaft. Install the balancer retaining bolt. Tighten the retaining bolt to 200-239 ft. lbs. (270-325 Nm).
  15. Install the inner fender shield.
  16. Install the right front wheel assembly. Tighten the wheel nuts to 100 ft. lbs. (136 Nm).
  17. Lower the vehicle.
  18. Install the belt(s).
  19. Reconnect the negative battery cable.
24X Crank Sensor
  1. Disconnect the negative battery cable.
  2. Remove the serpentine belt from the crankshaft pulley.
  3. Raise and support the vehicle safely.
  4. Remove the crankshaft harmonic balancer retaining bolt, then remove the harmonic balancer.
  5. Disconnect the sensor electrical connector.
  6. Unfasten the sensor bolts, then remove the sensor. Fig. 2: The 24X crankshaft sensor is secured by two bolts 86815103.gif
    To install:
  7. Install the crankshaft sensor to the engine with the two mounting bolts. Tighten the bolts to 8 ft. lbs. (10 Nm).
  8. Attach the electrical harness to the sensor.
  9. Using tool J-29113 or equivalent, install the harmonic balancer to the vehicle.
  10. Apply a thread sealer such as GM 1052080 or an equivalent to the threads if the crankshaft balancer bolt, then tighten the bolt to 110 ft. lbs. (150 Nm).
  11. Lower the vehicle.
  12. Install the serpentine belt.
  13. Reconnect the negative battery cable.

Dec 16, 2010 | 2003 Buick Rendezvous

1 Answer

Need to replace the crankshaft position sensor


REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Remove the serpentine drive belt from the crankshaft pulley.
  3. Raise and safely support the vehicle.
  4. Remove the right front wheel and tire assembly and the right inner fender access cover/splash shield.
  5. Using a 28mm socket, remove the crankshaft harmonic balancer retaining bolt.
  6. Remove the crankshaft balancer, using a puller if necessary.
  7. For 1992-99 vehicles, remove the CKP sensor shield. Fig. 1: If so equipped, remove the crankshaft position sensor shield 89634g95.gif

  8. Unplug the sensor electrical connector.
  9. For 1987-91 vehicles, perform the following:
    1. Remove the sensor and pedestal from the block face.
    2. Remove the sensor from the pedestal.
  10. For 1992-99 vehicles, remove the sensor from the block face. To install:
    1. For 1987-91 vehicles, perform the following:
    2. Loosely install the crankshaft sensor on the pedestal.
    3. Position the sensor, with the pedestal attached, on crankshaft sensor installation tool J 37089 or equivalent.
    4. Install the bolt to hold the pedestal to the block face, then tighten to 14-28 ft. lbs. (20-40 Nm). Fig. 2: Position the crankshaft sensor tool on the crankshaft 89634g76.gif
      Fig. 3: Insert the crankshaft sensor tool into the harmonic balancer 89634g75.gif

    5. Tighten the pedestal pinch bolt to 30-35 inch lbs. (3-4 Nm).
    6. Remove the special tool.
    7. Place the crankshaft sensor tool on the crankshaft balancer and turn. If any vane on the harmonic balancer touches the tool, replace the balancer.
  11. For 1992-99 vehicles, install the CKP sensor on the block.
    1. Install the retaining bolts and tighten to 14-28 ft. lbs. (20-40 Nm).
    2. Install the crankshaft position sensor shield.
    3. Attach the sensor electrical connector.
  12. Install the balancer on the crankshaft.
  13. Tighten the crankshaft bolt to 200-239 ft. lbs. (270-325 Nm) for 1987-91 vehicles. For 1992-99 vehicles, tighten to 110 ft. lbs. (150 Nm), plus an additional 76°rotation.
  14. Install the inner fender shield and the right tire and wheel assembly.
  15. Carefully lower the vehicle.
  16. Install the serpentine belt.
  17. Connect the negative battery cable.
prev.gif next.gif

Oct 29, 2010 | 1999 Oldsmobile 88

1 Answer

How do I replace mycrank sensor on a 1991 Buick Centry 3.3


Crankshaft Sensor REMOVAL & INSTALLATION 3.8L Engine On vehicles with a manual transaxles, the crankshaft position sensor is easily accessed from beneath the engine. On vehicles with automatic transaxles, the rack and pinion heat shield and the converter intermediate exhaust assembly must be removed first.
  1. Disconnect the negative battery cable.
  2. Disconnect the electrical connector at the sensor.
  3. Using a 28mm socket and pull handle, rotate the harmonic balancer until any window in the interrupter is aligned with the crank sensor.
  4. Loosen the pinch bolt on the sensor pedestal until the sensor is free to slide.
  5. Remove the pedestal to the engine mounting bolts.
  6. While manipulating the sensor within the pedestal, carefully remove the sensor and pedestal as a unit. To install:
  7. Loosen the pinch bolt on the new sensor pedestal until the sensor is free to slide.
  8. Verify that the window in the interrupter is still in the correct place.
  9. Install the sensor and pedestal as a unit while making sure that the interrupter ring is aligned within the proper slot.
  10. Install the pedestal and tighten the engine mounting bolts to 22 ft. lbs. (30 Nm).
3X Sensor
  1. Disconnect the negative battery cable.
  2. Remove the sensor harness connection to the sensor. Fig. 1: Unsecure the harness, then unfasten the bolt to remove the CKP sensor 86815102.gif

  3. Unsecure the sensor block bolt.
  4. Remove the Crankshaft Position (CKP) sensor from the vehicle. Inspect the O-ring for cracks and replace if needed. To install:
  5. Install the new O-ring if needed and lubricate with engine oil.
  6. Install the sensor into the hole in the block.
  7. Install the mounting screw and tighten to 71-88 inch lbs. (8-10 Nm).
  8. Attach the sensor harness connector, then connect the negative battery cable.
Dual Crank Sensor Sections 3 and 4 of this manual also cover testing, removal and installation, and adjustment of many computer controlled components.
  1. Disconnect the negative battery cable.
  2. Remove the belt(s) from the crankshaft pulley.
  3. Raise and support the vehicle safely.
  4. Remove the right front wheel and inner fender access cover.
  5. Remove the crankshaft harmonic balancer retaining bolt, then remove the harmonic balancer.
  6. Disconnect the sensor electrical connector.
  7. Remove the sensor and pedestal from the engine block, then separate the sensor from the pedestal. To install:
  8. Loosely install the crankshaft sensor to the pedestal.
  9. Using tool J-37089 or equivalent, position the sensor with the pedestal attached, on the crankshaft.
  10. Install the pedestal-to-block retaining bolts. Tighten to 14-28 ft. lbs. (20-40 Nm).
  11. Tighten the pedestal pinch bolt 30-35 inch lbs. (3-4 Nm).
  12. Remove tool J-37089 or equivalent.
  13. Place tool J-37089 or equivalent, on the harmonic balancer and turn. If any vane of the harmonic balancer touches the tool, replace the balancer assembly. NOTE: A clearance of 0.025 in. (0.635mm) is required on either side of the interrupter ring. Be certain to obtain the correct clearance. Failure to do so will damage the sensor. A misadjusted sensor of bent interrupter ring could cause rubbing of the sensor, resulting in potential driveability problems, such as rough idle, poor performance, or a no-start condition.
  14. Install the balancer on the crankshaft. Install the balancer retaining bolt. Tighten the retaining bolt to 200-239 ft. lbs. (270-325 Nm).
  15. Install the inner fender shield.
  16. Install the right front wheel assembly. Tighten the wheel nuts to 100 ft. lbs. (136 Nm).
  17. Lower the vehicle.
  18. Install the belt(s).
  19. Reconnect the negative battery cable.
24X Crank Sensor
  1. Disconnect the negative battery cable.
  2. Remove the serpentine belt from the crankshaft pulley.
  3. Raise and support the vehicle safely.
  4. Remove the crankshaft harmonic balancer retaining bolt, then remove the harmonic balancer.
  5. Disconnect the sensor electrical connector.
  6. Unfasten the sensor bolts, then remove the sensor. Fig. 2: The 24X crankshaft sensor is secured by two bolts 86815103.gif
    To install:
  7. Install the crankshaft sensor to the engine with the two mounting bolts. Tighten the bolts to 8 ft. lbs. (10 Nm).
  8. Attach the electrical harness to the sensor.
  9. Using tool J-29113 or equivalent, install the harmonic balancer to the vehicle.
  10. Apply a thread sealer such as GM 1052080 or an equivalent to the threads if the crankshaft balancer bolt, then tighten the bolt to 110 ft. lbs. (150 Nm).
  11. Lower the vehicle.
  12. Install the serpentine belt.
  13. Reconnect the negative battery cable. prev.gif next.gif

Sep 24, 2010 | 1992 Buick Century

1 Answer

BANGS LOUDLY ON FINAL SPIN


Pull the lower front panel off and check the filter on the pump housing. If it is restricted it may not be getting enough water out of the clothes before the spin starts. Do you have it on pedestals? Sometimes this exaggerates the vibrations due to the raised center of gravity.

Apr 30, 2010 | Kenmore HE2 Plus Front Load Washer

1 Answer

Crankshaft Position Sensor and Camshaft Position Sensor


REMOVE OR DISCONNECT

  1. Serpentine belt from the crankshaft pulley.
  2. Raise the vehicle on a hoist.
  3. Right front tire and wheel assembly.
  4. Right inner fender access cover.
  5. Using a 28 mm socket, remove the crankshaft harmonic balancer retaining bolt.
  6. Crankshaft harmonic balancer using tool J 38192 or equivalent.
  7. Sensor electrical connector.
  8. Foreign object deflector.
  9. Sensor and pedestal from block face.
  10. Sensor from pedestal.
INSTALL OR CONNECT:

  1. Loosely install the crankshaft sensor on the pedestal.
  2. Position the sensor with pedestal attached on special Tool J 37089.
  3. Position the special tool on the crankshaft.
  4. Bolts to hold the pedestal to the block face, torque to 20-40 Nm (14-28 lb.ft).
  5. Torque the pedestal pinch bolt to 3-4 Nm (38-40 lb.in).
  6. Remove special tool J 37089.
  7. Place the special tool 37089 on the harmonic balancer and turn. If any vane of the harmonic balancer touches the tool, replace the balancer assembly.
  8. Balancer on the crankshaft.
    • Apply thread sealer (GM 1052080) or equivalent to the threads of the balancer bolt.
  1. Torque the crankshaft bolt to 140 Nm + 56°(104 lb.ft + 56°).
  2. Foreign object deflector.
  3. Electrical connector.
  4. Inner fender shield.
  5. Tire and wheel assembly, torque to 140 Nm (104 lb.ft).
  6. Lower the vehicle.
  7. Serpentine belt.

Jun 02, 2009 | 1994 Buick Regal Gran Sport

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1460 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Brad Brown

Level 3 Expert

15557 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...