Question about Dual XDM-6820 CD Player

1 Answer

Someone stoled my face plate will another face plate from a XDM 6820 work?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 105 Answers

Yes as long as it is the exact same brand & same model# it will work

Posted on May 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Xdm260


Face wont light up it has power

Jun 18, 2014 | Dual XDM-6820 CD Player

3 Answers

Would metal touching circuit cause radio to not work


Ssurely. If any metal contacts to the circuit board, during the set is powered, will cause a short circuit, and damage to components.

May 14, 2014 | Dual XDM-6820 CD Player

1 Answer

My xdm6820 has no display showing. What do you sugest? Any ideas? It works fine but can not see clock or radio station. No display at all!!


There are two 3mm white LEDs inside the face-plate that need to be replaced. Remove the face-plate and turn it over. Remove the 4 screws in the corners. Un-snap the plastic back off the face-plate. This exposes the back of the printed circuit board. Pull the volume knob off the front of the face-plate. You may need to use a small screw driver to gently pry it up. Flip the face-plate back over and remove the one screw that's holding the printed circuit board in. Separate the printed circuit from the front of the face-plate. Be careful to not lose the spring for the push pin. Flip the printed circuit board over and you'll see a raised metal box surrounding the display. The one end of this metal box is covered in black tape. Remove this tape to revel a small cavity in the side of the metal box with two 3mm white LED in it. These are the 2 LEDs that need to be replaced. This cavity is so small there's not much working room. Note that the positive terminal for each of these LED is on the left and the negative terminal is on the right. Rather than un-soldering the old LEDs I found it easier to use a small pair of diagonal cutters to just cut their leads and then pull them out of the cavity. Leave enough of the old leads sticking up to solder the new LEDs to. Trim the leads of the new LEDs to the proper length, slide them into the cavity one at a time and solder their leads to the stubs of the old leads. Make sure you get the polarity correct. Put everything back together and you should be good to go. I hope this helps you out.

Dec 20, 2009 | Dual XDM-6820 CD Player

1 Answer

Error 2


I am sorry, I don't get involved with serious Electronics and Computer problems

May 23, 2009 | Dual XDM-6820 CD Player

2 Answers

I have no display lights on my dual xdm6820 car radio. It does work but I can't see any words or graphics on the front of the unit. Can you tell me what is wrong?


if you have connected all the wires correctly you probably have a faulty dash,
If it is a removable face take it off and clean the terminals and re connect.
Hope this helps

May 07, 2009 | Dual XDM-6820 CD Player

1 Answer

My dual xdm6820 doesnt turn on and theres a red binking light behind the face plate next to the reset button


Probably you are mising 1 voltage,check this you need to have 2 voltages ok,1 voltage has to be present on the yellow wire(constant voltage,means all the time,ok) and the second voltage on the red wire (this voltage has to be switched wiht the ignition key)check this and try to fix the problem,probably there is a fuse blown,you can use a tester light to check the 2 voltages.or if you dont want to do this just conect the yellow and red wires together and the unit has to turn on.

Mar 24, 2009 | Dual XDM-6820 CD Player

4 Answers

Face plate replacement


You can't find faceplates for card decks since that will defy the safety feature.

Mar 19, 2008 | JVC KD-AVX33 Car Video Player

1 Answer

Display comes on then cuts completely out


Hello. here is the solution...if you still need it..

Open up the face plate... by unscrewing the 4 screws at the back corner of the faceplate

Expose the PCB with the LCD display mounted on it...
towards the right is black tape... remove the tape.
this exposes 2 White LED ( 3 mm) tapering inside the cavity of the LCD display..

If the symptoms are what u say... then the LED's are dead...

Unsolder the bad LED's with new ones.... and then fix everything back

hopefully everything works.. Cheers.

Nov 11, 2007 | Dual XDM-6820 CD Player

Not finding what you are looking for?
Dual XDM-6820 CD Player Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dual Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4874 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Dual Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...