Question about Craftsman 20 Hp 42" Deck Lawn Tractor

1 Answer

I have a craftsman dlt2000 mower and the blades r ingaging about half of normal speed with out even pulling the knob out

Posted by on

  • Anonymous May 18, 2009

    the deck belt looks ok but is there more belts up inside

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

Could be a belt problem

Posted on May 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Craftsman lt 2000 42


Hi, first check the spring that pulls on the idler pulley for lost tension then run the blades for a 10 to 15 minutes at half to full throttle. This is necessary to bed the new belt into the old pulleys. Regards Phil.

Sep 05, 2012 | Garden

1 Answer

Have a craftsman mower just purchased riding how do I get the blades to work so can cut yard


if it is a newer model while on the seat there should be a yellow or red knob you pull out to turn on the blades they will not work in reverse(a safety thing)

Jun 28, 2012 | Craftsman Garden

1 Answer

Blades don't ingage


look and see if the belt came off the pulleys, it could be at the front pulley or at the rear pulleys. lower the deck all the way down and look.

Jun 12, 2012 | Craftsman Garden

1 Answer

Craftsman dlt2000 20 hp kohler runs great until i try to engage blades pull up on the switch to engage and motor bogs and stalls


Now is a great time to remove the deck and sharpen the blades! In the process, you will find your problem. Look for clogs, seized bearings, freely rotating belts, etc... The problem is in the deck or drive belt. Hope this helps!

Sep 26, 2011 | Craftsman 17.5 hp 42 in. Deck Lawn Tractor...

1 Answer

Craftsman Mower - 625 Briggs and Stratton Engine. The mower starts after I prime it 3 times. Starts up and runs at only half speed. I have taken the whole thing apart, changed the gas, cleaned the carb,...


Check the governer, its a lever that pulls the throttle plate from the engine side. Try manually overriding it (twist it open as the engine's running) and see if that does it.

May 09, 2011 | Craftsman 675 Torque 190cc 21" Briggs ...

1 Answer

Blades wont ingage on my craftsman lawn tractor #917.274811?


After hitting a tree root, blades will not cut when I press to engage

Aug 05, 2010 | Craftsman 20 hp 42 in. Deck Lawn Tractor -...

2 Answers

My riding lawnmower blades will not disengage or engage Now my lawn mower will not start


just replaced some pulleys on my craftsman 42 inch cut and now the blades are ingages all the time, but it will start

Jul 17, 2010 | Craftsman 42 in. Deck 19.5hp Lawn Tractor

1 Answer

CRAFTSMAN 26 HP 48'' DLT2000 MOWER ELECTIC PTO CLUTCH SEIZED UNPLUGGED BUT BLADES CONTINUE TO TURN. CAN IT BE REPAIR OR MUST IT BE REPLACED?


I would say replaced to ensure correct opperation.Thanks for asking and I hope this helps out.Please leave me 4 thumbs up.

Jul 20, 2010 | Craftsman 26 Hp 54" Deck Yard Tractor

1 Answer

When I pull the blade lever the blades do not turn. Found that the trottle wire to pto is broken. Need instructions and a diagram on how to fix it. Thanks


just wire it back together, you don't have to worry about crossing the wires up. because it's just a hot and ground for a coil to magnitize to ingage the pto clutch.

Jun 21, 2010 | Craftsman 20 hp 42 in. Deck Lawn Tractor -...

3 Answers

Craftsman GT5000: Dies when switch is pulled to engage blades


Hi
Check for burnt fuse behind dash. If no burnt fuses check if getting power to magnetic clutch mounted on bottom of engine crankshaft. Make sure wires are not broken by magnetic clutch. Make sure the safety seat switch is working. Make sure you are sitting on the seat when you try to engage the blades. If that does not work try pushing and wiggling the seat sensor. Check make sure wire is attached to safety switch under seat.

Apr 04, 2009 | Craftsman 20 hp 42 in. Deck Lawn Tractor -...

Not finding what you are looking for?
Craftsman 20 Hp 42" Deck Lawn Tractor Logo

Related Topics:

251 people viewed this question

Ask a Question

Usually answered in minutes!

Top Craftsman Garden Experts

Dean Gruber

Level 2 Expert

110 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Dennis Key
Dennis Key

Level 3 Expert

2475 Answers

Are you a Craftsman Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...