Question about Behringer iNUKE Series 3000W Stereo Power Amplifier NU3000DSP

1 Answer

Output blown inuke 3000

No sound

Posted by Anonymous on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Expert
  • 432 Answers

The problem is that nobody sends a good photo from the inside, then it would be easy, instead of guessing. If you know you've overpoweted it and didn't gave it time to cool down a couple of days before.... Down forget that the safety options ain't accurate on these produkts.
when you used it with low ouput values, i would first measure if there is a dc or ac voltage at your outputs. And it depends if you have guarantee or niet: if you have, send it it back, if you know you've abused/overpowered a unit, just open it and take some onternal pics and send them. You know best what you've done with your unit.

Posted on Oct 12, 2014

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

No center channel sound on my Yamaha receiver

Is the center channel amp blown? How about checking the center channel input wire for signal?

Jan 06, 2017 | Yamaha Audio Players & Recorders

1 Answer

How do i put my behringer inuke 6000 dsp in stereo mode?

Behringer iNUKE NU6000DSP
Stereo mode is set by the DSP processor ( I/O amp mode). The link above will lead you to the manual. On the main page go to "documentation" and to "manual , English". Review and study the functions of the DSP processor. Yo'll nedd to find I/O amp mode.

Jun 02, 2014 | Behringer NU6000DSP iNuke 6000-Watt Power...

1 Answer

Behringer inuke 3000 goes into protection mode when turn on. What is the problem?

Might be that a simple screw is loose or temp protector, but often the mute/ power off with these simple units is done with a capacitor and resistor, there would be the first thing to watch, just check which ic regulates the the power on/off mute ic

Sep 10, 2013 | Behringer iNUKE Series 3000W Stereo Power...

1 Answer

My Swann DVR8-3000 HDMI output on LGTV is red all over but the video is visible,I tried restoring the default setting and even tried adjusting the resolution but no luck.Could it be that the HDMI output is...

have you checked the system on another tv. or monitor. if is the same on these then the graphics on the dvr has gone wrong. if its is just on the tv hdmi then you have had the tv on the hdmi for a to longer period and blown the reader board for the hdmi.

Aug 12, 2013 | SWANN DVR8-3000 TruBlue 8 Channel D1...

1 Answer

I am an electronics hobbyist. My Peavey Escort 3000 was not powering up. Prior to this state, the power LED would come on for just a second and then go out. This would happen repeatedly whenever I turned...

Sounds like a regulator IC has blown. if you can replace these and then check the output before putting the caps in you can find out. You may have taken other circuitry out if it was enough over-voltage to cause the caps to blow.

Aug 11, 2013 | Peavey Escort 3000 300 Watt Portable PA...

1 Answer

Behringer How To Connect iNUKE6000DSP

The manual is very clear and if you then still understand it, can you please tell whatt you all want to connect and on which in or outputs.
Nobody can do a thing with this data .
greetings richard

Jun 19, 2013 | Behringer iNUKE NU6000DSP High-Density...

1 Answer

No sound on pioneer dph-3000

If you can check all of your speakers and speaker wires for shorts and/or grounds. If they all check out good, you may have a blown output ic.

Mar 20, 2012 | Pioneer Car Audio & Video

1 Answer

Generator is fast running and has blown 2 power tools and cement mixer

Use a meter and adjust to 3000/3600rpm or 50/60Hz. Then check output voltage to be in range 230/115V depending on which country you are in. Adjustment is done on the governor to throttle linkages.

Nov 13, 2010 | Honda Electrical Supplies

1 Answer


If you go to Device manager under sound,video and game controllers you should see audio codecs.Right click and choose update driver.

Aug 10, 2008 | Acer Aspire 3000 Notebook

Not finding what you are looking for?
Behringer iNUKE Series 3000W Stereo Power Amplifier NU3000DSP Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Behringer Audio Players & Recorders Experts


Level 3 Expert

5047 Answers

Alvan Dawkins
Alvan Dawkins

Level 1 Expert

2 Answers

The Knight
The Knight

Level 3 Expert

74106 Answers

Are you a Behringer Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides