Question about Maytag Performa PAV2200

1 Answer

Does not spin in most cycles

Our washer PAV2000AWW stopped spining in the regular cycle right before rinsing. I had to move the cycle to the final spin and then it would spin. Of course I then had to go back to the rinse option and then it would rinse and spin correctly. After a while, the spin on the rinse cycle stopped. So I had to move it to the spin in the next (delicated clothes) option. Same problem. After a while, I found myself moving the switch way forward to the next and next spin cycle. Currentl, only one spin options works. How does this happen? What is the problem? Is it the switch?



Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 94 Answers
Re: Does not spin in most cycles

It sounds like your timer is defective.  If this is the case you will have to replace it.

Posted on Oct 17, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Why does a Kenmore washer not finish the cycle?

Washer Repair - Not Advancing -Repair & Diagnostic ...

? 8:30
Sep 6, 2013 - Uploaded by
Repair your Kenmore Top Load Washer suffering from these following issues: Will Not Advance Past Rinse ...

Kenmore washer doesn't complete final spin cycle - ApplianceBlog
May 16, 2012 - 9 posts - ‎2 authors hello, my kenmore washer doesn't complete the final spin cycle. i ... Does it stop in the middle of the final spin cycle or does it not go into the ... FIXED Kenmore Washer - Not finishing the spin cycle
9 posts
Dec 20, 2014
FIXED Washing Machine Does Not Complete Cycle ...
10 posts
Mar 14, 2013
FIXED Kenmore washer won't spin out all water from ...
10 posts
Jun 27, 2009
FIXED GE front load washer WCVH6260F0WW stops ...
10 posts
Jul 2, 2007
More results from

Nov 05, 2015 | Kenmore Washing Machines

1 Answer

Roper washer new will not fill with warm water on rinse cycle it fills and spins

if its only a new machine make sure transport bolts have been removed

Apr 09, 2014 | Roper Washing Machines

1 Answer

Kenmore Washer Doesn't Agitate

Don't be too sure the drive coupler hasn't failed or is failing

Jun 15, 2013 | Kenmore 24032\24036 Top Load Washer

1 Answer

Washer is full of water but will not spin

if your washer has old dial selector ,does it continues and finishes "cycle" without spining or does the selector stops moving also you could have a bad timer ,newer ones will have some sort of electronic module

Feb 23, 2012 | Kenmore Washing Machines

1 Answer

Whirlpool Washer Stop Working after Agitate

Good day,
If it goes thru the wash cycle normally then quits, it is the lid switch assembly.
To remove the top console, be aware there are 3 locations for the screws. Bottom left and right. Bottom left and right but covered by plastic end caps that have to be unsnapped, and finally, bottom rear.
There are also 3 different lid switch styles, so use the complete model number or take the old one in to the supply house.
Here is a good tutorial on the change out procedure.

Mar 05, 2010 | Whirlpool Washing Machines

1 Answer

Final spin /rinse cycle won"t stop

It's usually a control board problem. sorry for the bad news :(

Jul 07, 2009 | Maytag EPIC MFW9700S Front Load Washer

1 Answer

Washing machine won't rinse or spin

sounds as if you have a faulty lid switch, for safety reasons if the machine doesnt think the lid is closed it willnot spin/drain the waer out.

Feb 23, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Will only work on cycle, will not agitate in the other cycles

Thanks for your question You say it works on one cycle but not the other lets sat you start a regular wash ,the washer should fill ,wash for the minutes you have set, pump out the water #spin , Stop fills & rinse stop pump out water &spin If you try a delicate cycle and it does not do what it did on regular cycle . You have a timer problem . Thanks for your question hope i helped you solve it . THE APPLIANCE DOC

Sep 09, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

I also need the answer...

where is the lint trap located

Dec 06, 2007 | Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

394 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Al Clark

Level 2 Expert

290 Answers

Todd Marr
Todd Marr

Level 2 Expert

77 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides