Question about Autotek XS-900.2 Car Audio Amplifier

1 Answer

Problems with the ampli

The problem is that the ampli is burning my subwoffer i need to located a service center hear in mexico so i can fix it. please answer me a son as you can. fcarrillo@propesa.com.mx

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Can i joine the ampli with computer

Posted on Nov 18, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Burned resistor


I had two of them like this. Order resistor at Digikey. Match the resistor color rings to the online decoder at Digikey so you get the right one. Refresh the Ni-cd battery while you're in there. Search "youtube" for battery fix. It's easy to do.

Feb 02, 2013 | Bissell SpotLifter 2X Portable Deep Carpet...

1 Answer

When switching on the ampli, I get a message "amp


you may have a shorted speaker wire. unhook all the speakers and test each speaker by using a 9 volt battery across the speaker wires, you should hear a pop (this will not hurt your speakers). in each speaker. if you don't hear the pop then you may have found the one that is shorted. Another thing you can try is to unhook all the speakers and trun on the system (briefly) and see if the message is gone, this being further indication that you have a shorted speaker wire.

Mar 20, 2011 | Harman Kardon AVR 130 Receiver

3 Answers

My sony wega not start


If your SONY will not start and it is blinking the 6 or 7 blink code you can fix this by installing a new IC at location IC6501 and IC8002. You use the same IC's at both locations and they can be purchased on eBay for about $20. for a package of 4. the #s on the IC are: MCZ3001D and 0542D - they control the horizonal deflection circuit. Good luck.... OR you can pitch the TV because as I believe SONY's are junk. They are made in Tijuana Mexico.

Oct 19, 2009 | Sony FD Trinitron WEGA KV-32FS120 32" TV

3 Answers

LG Refrigerator; light stays on, not cooling


There is a recall for that problem the main board is bad. Contact LF for advise

Oct 14, 2009 | LG LFC25760 French Door Refrigerator

1 Answer

I am searching for a Service Center in the Albuquerque, NM area. I have a HP Laserjet 2840, that is needing a fuser 52.0. Can you help me? Betty


Before travelling to the HP Resellers location, please phone to confirm opening hours and availability of the product you are seeking.

Data Terminal Service Inc (DTS)
715 Rankin Rd NE Ste A
Albuquerque New Mexico 87107
Phone No : +1-505-3451611

Omnitek Inc
326 Washington St SE
Albuquerque New Mexico 87108
Phone No : +1-505-2650552

Document Solutions Inc
4121 Prospect Ave NE
Albuquerque New Mexico 87110-3817
Phone No : +1-505-2569579


Albuquerque Image Products
4406 Towner NE
Albuquerque New Mexico 87110
Phone No : +1-505-8816266


Computer Corner
4410 Menaul Blvd. NE
Albuquerque New Mexico 87110
Phone No : +1-505-8812333


Networx Inc
7201 Washington St NE
Albuquerque New Mexico 87109-4547
Phone No : +1-505-3460700

Sep 16, 2008 | Office Equipment & Supplies

1 Answer

HTS 3450 subwoffer off


I have a similar problem. I inspected the power board and found IC901 burned completely. I cannot find out the part number and have tried to get a reply from phillips but have not heard back from them. Anyone have a schematic or can give me the part # of IC901?

Sep 06, 2008 | Philips HTS3450 System

1 Answer

Ps2 problom


All you can do is try cleaning the laser lens. Use a lens cleaning disc and let it run about 20 to 30 seconds.

If the problem is the lens needing to be cleaned, this will fix it. If you continue to have the same problem the laser pick up is bad.

You cannot take it to any shop, it must go to Sony's factory service located in El Paso Texas, they will then send it across the border to Mexico where Sony moved their factory service center to.

Parts are not available for the Playstations. Sony will not sell parts for the Playstion to any repair center.

I know this for a fact. I work at a Sony authorized service center and we can not even get the parts there.

The problem you are having is the most common problem with the Playstation.

I know this is not very good news, but it is the truth.

I hope you found this information helpful, and if you did a good rating would be appreciated, and appropriate since it is the correct answer.

Let me know if I can be of any further help.

Jun 22, 2008 | Sony PlayStation 2 Slimline Console

3 Answers

Playstation 2 console will not read disc


The problem here is the lens you might have touched it accidentally. You can bring it to a shop to have lens changed or remodify your console.
Thanks!

Jun 20, 2008 | Sony PlayStation 2 Slimline Console

1 Answer

Samsung SYNC SGH-A707


you've got faulty (p.a. power ampli) this can be fix only by professionals go to your nearest service center.... hardware problem..

Apr 13, 2008 | Samsung SYNC SGH-A707 Cellular Phone

Not finding what you are looking for?
Autotek XS-900.2 Car Audio Amplifier Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Autotek Car Audio & Video Experts

Morne Olivier

Level 2 Expert

257 Answers

Tom Chichester

Level 3 Expert

45970 Answers

FastHarley
FastHarley

Level 3 Expert

637 Answers

Are you an Autotek Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...