Question about Frigidaire 14 Cycle Tumble Action Washer

2 Answers

Frigidaire Tumble Action Washer - lights flash, beeps, does nothing else...

My washing machine went on the fritz.  It tries to start (door locks, appropriate lights are lit), then after about 10 seconds the 5 vertical lights above the pause/cancel button flash green every 4 seconds.  For the first 5 minutes, the flashing is accompanied by a beep.  After 5 minutes, the beeping stops, but the flashing continues.

What gives?

Posted by on

  • 3 more comments 
  • rosecutter Oct 17, 2007

    Model LTF2140ES0

  • Kitacooda Feb 15, 2008

    After loading the washer and pressing the appropriate buttons, I press start. The door locks... but then nothing happens. I've tried a few of the programs, but the same thing happens on each one. The timer will count down (very slowly), but there's no action from the washer.

  • loismodlin Jan 28, 2009

    When I push the start button the door locks but the washer will start the water going into the washer

  • pfloyd Jan 29, 2009

    My washer will not start the cycle. I select the cycle press start and the counter counts down a few moments and then the counter and all the lights go off. Any suggestions?

  • Anonymous Mar 21, 2014

    I put some sheets into my Kenmore 48102 washer, closed the door, and the lights started flashing and beeping...9 times, pause 2 seconds, 9 times....continuously! I've tried holding down different buttons at once and unplugging the machine for an extended period. But the flashing/beeping resumed immediately upon being plugged in again. A friend said that hers had done the same thing and she'd removed the top and replaced the mother board. Can you tell me how to do the same...if that is indeed what is wrong with it?



2 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

If you have had a lightning storm or power surge it may have fried the electronics panel. That is what happened to mine. Once it is fixed you should put a surge suppressor on it that is rated for major appliances.

Posted on Apr 27, 2008


Have you had a storm or power surge lately. May need a new electronics panel installed. That is what happened to mine. Once it is fixed, you should get a surge suppressor that is made for major appliances

Posted on Apr 27, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

3 Answers

LTF2140ES0 washer just beeps three times, wont start

Frigidaire engineers are so smart they programmed it to beep 3 times for door lock problem, draining problem and other problems in the internal electronics and didn't bother to give the users specific info to read off the machine.

Oct 30, 2008 | Frigidaire 14 Cycle Tumble Action Washer

1 Answer

Control lock is lit, door opens but not able to wash

Hold the control lock button for 5 seconds till the light goes off.

Jun 10, 2017 | Washing Machines

1 Answer

WFW94HEXW door won't unlock and Door Lock isn't lit

if you machine is warranty you must call to the whirlpool, and get the assistance via online chat. However you must wait about 180 seconds since you did the command STOP, and stop the motor, fi the water level is higher must be drain before the latch door unlock.
2) if do not obey press and hold END OF CYCLE, wait about 10seconds
3) reset the machine unplugged from wall by 45 minutes, and then plug again, and turn on and unlock the door

God bless you

Jun 21, 2012 | Washing Machines

1 Answer

My washing machine will not start the control lock button is lit up and I cannot turn it off

If you have a front loader then Press and hold the "end of cycle" button for 5-10 seconds and it will reset the child safety lock.

Jun 16, 2011 | Maytag Washing Machines

1 Answer

My whirpool locked light keeps flashing and wont wash


The light is flashing due to the door lock error. The door lock is activated as the machine experienced an error or was stopped in middle of a cycle. Or the door was being pulled while the machine was running a cycle. Try unplugging your washer and restart the washer to check if you are still getting the same blinking light. If error is still not resolved then start the rinse/spin cycle & stop the cycle, now press and hold the cancel button for 5-10 seconds. However, if you are still not able to get the door open then you'll need to open the door manually by disassembling the washer.
Hope this helps... Please post back for any further assistance.


Apr 18, 2011 | Washing Machines

Not finding what you are looking for?
Frigidaire 14 Cycle Tumble Action Washer Logo

1,583 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

Jason Harris
Jason Harris

Level 2 Expert

272 Answers

Charles T Nevin
Charles T Nevin

Level 3 Expert

4070 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides