Question about One For All URC-3021 Remote Control

1 Answer

I can use the channel changer for channels 2-13 however I have to push the individual channel numbers for everything else.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,285 Answers

Have you tried to make any channel higher than 13 a favorite ch (program channels that you enjoy and save it) this can also be done on a cable converter box. and any time you want you can go through the loop of channel that you just saved . look at the booklet that came with remote

Posted on May 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Scanner stuck on one channel and won't allow me to enter new freq


Push the "L/O" lockout button and it will lockout that channel.
When you press "Scan" you have to have at least one of the banks scanning, so press 1, 2, 3,....9, 0 whatever bank you have channels programmed in order to automatically scan. You should be able to press "Manual" to see each channel individually.

May 07, 2014 | Uniden Bearcat BC 220XLT Radio Scanner

1 Answer

My vizio changer hard to chg channels have to push hard and move changer around to change channels. I put new batts.still does it. been like that for awhile


Some liquid may have been spilled onto this remote. As the liquid dries, a film is left on the circuit board inside.

Carefully take the remote apart and clean the circuit board with rubbing alcohol.

Take the rubber membrane that has the remote buttons on it, and clean the back side that touches the circuit board when you press a button.

Allow everything to dry completely and put the remote back together.

May 18, 2011 | Vizio L32 32 in. LCD HDTV

1 Answer

I have an Element 32" LCD TV that is 3 months old. Everything works except I can't change the channels. If I push the channel number, it will go to that channel, but if I try to use the remote or the...


I talked to the manufacturer & they said that all I needed to do was to run the channel search, uninterupted, again. I did it & everything works. Thank you for your input.

Mar 19, 2010 | Element Electronics FLX3210 32 in. LCD TV

1 Answer

RCA Colortrak 2000 remote control will do everything except change channels.  I have Insight coax cable, just having disconnected from Direct TV satellite connection--only because new apartment does not...


I called RCA's 800 number on the back of the owner manual--got a response that said to replace the unit since only the up-down channel changer buttons were not working. Using another remote (universal) now--cost only $5.

Dec 13, 2008 | Akai LCT2701AD Television

1 Answer

Channel changer locks up


Make sure you have the tuner set for digital channels only. then redo the channel search.

May 06, 2017 | Hitachi 57F500 57" Rear Projection...

2 Answers

No freaking signal


Double check ALL your ant wire connections. Then reprogram the converter to check for stations again. If that doesn't work then reposition your antenna and reprogram again.

May 21, 2008 | Insignia Digital-to-Analog Converter for...

1 Answer

TV channels


Sounds like it lost programing, if it has an "auto program" feature try that, or some older models need it to be done manualy and have a "add/erase" feature, instructions for that should be in your owner's manual.

Oct 31, 2007 | Televison & Video

Not finding what you are looking for?
One For All URC-3021 Remote Control Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top One For All Televison & Video Experts

Computer Repairing
Computer Repairing

Level 3 Expert

14641 Answers

The Knight
The Knight

Level 3 Expert

74243 Answers

Cindy Wells

Level 3 Expert

5126 Answers

Are you an One For All Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...