Question about Computers & Internet

1 Answer

Light quit working, all the other buttons work.

Posted by on

  • jtg1two May 18, 2009

    the wheel and buttons, just the light at the bottom don't work.

  • Jeff May 11, 2010

    What light are you talking about? The one under the mouse or something else? What make and model mouse is it? is there any movement on the screen when you move the mouse?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 192 Answers

If the buttons can activate functions, usch as the rihgt button bringing up the menu, but the light at the bottom no longer comes on and there is no movement, then the source is defective and you will need to replace the mouse. These are no repairable, since the cost for the work is much higher than replcing the mouse.

Posted on May 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Signal lights only work intermittenly


The blinker relay is getting worn out. It's right behind the hazard lights switch. Pull off the black trim around the radio, hazard, ets, and the relay is write there. Next time the blinkers stop working hit the hazard button or hit the trim just above the hazard lights button. Mines been doing it off and on and I just hit the trim above the hazard button and they start blinking again. Never have time or remember to get a new relay.

Sep 07, 2014 | 2001 Pontiac Grand Am SE

1 Answer

Why does the tanks/battery lights quit working?


all the wires run off the solenoids under the hood. one for the coach. one for the chassis. also chech all fuses under hood for the coach side. make sure have good contact.

Jun 12, 2014 | Keystone 2013 Cougar Xlite 32SAB

1 Answer

Problem with start button.


I suspect the start button. In many bikes the start button deactivates the headlight to provide full power for starting. This continuous load works the button mechanism quite hard.

Mar 23, 2014 | 2005 kawasaki EN 500 Vulcan

1 Answer

Our sharp r520lw just quit working, timer works, light works, all buttons work, (clear, etc) however turntable doesn't work and no


That would be a bad bottom door switch or its mount.

See the help file on door switches here.

See the service manual here.
We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

Dec 13, 2011 | Sharp R-520LW Microwave Oven

1 Answer

Tv remote quit working


The remote put out IR (INFRARED) signal that human eyes cannot see, you need to use your digital camera to see it, just point the remote at the camera's lens, you should see flashing light on your camera screen when any remote buttons is pushed.
You may have problem with the IR receiver in your TV, but find out first if the remote is putting out the signals
Parts:
http://www.shopjimmy.com/vizio-3642-0022-0189-ir-sensor.htm

worst case will be the main logic board.
http://www.shopjimmy.com/catalogsearch/result/?q=VX32L

http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide

http://s807.photobucket.com/home/budm/allalbums

Jun 28, 2010 | Vizio L32 32 in. LCD HDTV

1 Answer

I can't select a cycle. The buttons quit working.


it sounds like the touchpad is gone,phone the manufacture and see how much it will cost ,and then take it from there

Mar 30, 2010 | Maytag 24 in. MDB7601AWS Stainless Steel...

1 Answer

Logitech wireless rf keyboard and mouse quit


Hi,

To fix the problem,
please press the connect connect button on the bottom of the mouse and the connect button on the reciever and relaese both the buttons together. this would rest the wireless connection and then the mouse should work fine.

regards.

Jan 28, 2010 | Logitech Wireless Access Duo Optical...

1 Answer

Mouse just quit working, installed new batteries red light works


Normal 0 Make sure that the batteries are good then do the following.

Turn the mouse over and find the small rest/connect button on the bottom of the mouse and press it. This should connect the mouse to the receiver and work properly. If not, try pressing the receiver button and then press the button on the mouse. This should be done whenever you change batteries or glitch.
Hope this helps you. Bud

Dec 07, 2009 | Logitech Cordless Mouse

1 Answer

The touchpad on my microwave has quit working.


possibly a stuck button which would mean a replacement pad, do the buttons bleep when you push them do some work and others dont its quite common normally its the start button or the cancel which goes(due to constant pushing) and it causes the error alternatively its a possible logic board fault which is far more expensive to replace!

Nov 12, 2008 | Microwave Ovens

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...