Question about Canon MF8180C Color Laser MFC Printer

1 Answer

Err 99 appears after every click for canon eos 30 D

I have eos 30 d body for repair with me It gives err 99 after putting battery and trying to click it.Afterwards it doesn't turns off also,I have to remove battery for that.can u guide me in that case in which board problem may be existing

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 433 Answers

Err 99, but lens-to-body problems are common- thought error 99 is a bit of a catch all- generally a lens and body conflict. And also Err 99 means that something wrong happened, but then it cleared out before it could be further determined.
Here is the blurb from canon to try:

Thank you for contacting Canon product support. I'm sorry to hear that
your EOS 10D is displaying an "ERR 99" message.

To isolate the cause of the issue, we suggest that you do the
following:

1. Turn off the camera.
2. Remove the lens, battery, and CF card.
3. Allow the camera to sit without power for approximately 20 minutes.
4. Insert a fully charged battery, and turn on the camera.

Does the "ERR 99" message appear? If it does, then the camera should
be serviced. If it does not, then please proceed to the next set of
steps:

1. Turn off the camera.
2. Insert the CF card.
3. Turn on the camera.
4. Format the CF card in the camera.

Does the "ERR 99" message appear? If so, then the CF card is the most
likely source of the issue. Try using a different card.

If the message does not appear, please complete the following steps:

1. Turn off the camera.
2. Clean the lens contacts by gently rubbing them with a pencil eraser
or soft cloth. Be careful that you do not let any debris fall into the
camera body.
3. Reattach your lens.
4. Turn on the camera.

If the "ERR 99" message only appears when one particular lens is
attached, then that lens should be examined by a service technician.

If you see the "ERR 99" with a different Canon lens attached, then the
camera should be serviced.

For factory service, forward your digital camera (remove the CF card
and battery) properly packaged and insured, with a letter describing the
difficulties. Be sure to include your name, address, telephone number,
and proof of warranty (if applicable). Send to the Canon Factory
Service Center at the following address:

Canon Factory Service Center
100 Jamesburg Road
Jamesburg, NJ 08831
Tel.# (732)521-7007

or

Canon Factory Service Center
15955 Alton Parkway
Irvine, CA 92618
Tel.# (949) 753-4200

Your equipment will be examined and you will be advised of the
findings.
The length of time for the repair will be dependent upon the nature of
the repair and availability of parts if needed. If the repair entails
something that is not covered in warranty you will be sent a written
estimate to the address that you have provided.

Please leave for me, a rating...

Posted on May 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix err,30 on canon t3


Have a look here for error code 30

http://www.canon.co.uk/support/consumer_products/product_ranges/cameras/eos/error_codes/

Jun 20, 2014 | Canon EOS 1100D Rebel T3 Body Only Digital...

3 Answers

Canon EOS Digital Rebel XTI 400D Displays Err 99. Problem with CF card. Replaced with brand new card-still same err 99 camera is totally charges, acts dead, keep flashing Err CF, I try to format, it...


Hi,

1. Turn off the camera.
2. Remove the lens, battery, and CF card.
3. Allow the camera to sit without power for approximately 20 minutes.
4. Insert a fully charged battery, and turn on the camera.
5. Depress the shutter button as you would to take a picture.
Does the “ERR 99′ message appear? If it does, then the camera should be
serviced. If it does not, then please proceed to the next set of steps:
1. Turn off the camera.
2. Insert the CF card.
3. Turn on the camera.
4. Format the CF card in the camera.
5. Depress the shutter button as you would to take a picture.
Does the “ERR 99′ message appear? If so, then the CF card is the most
likely source of the issue. Try using a different card.
If the message does not appear, please complete the following steps:
1. Turn off the camera.
2. Clean the lens contacts by gently rubbing them with a pencil eraser
or soft cloth. Be careful that you do not let any debris fall into the
camera body.
3. Reattach your lens.
4. Turn on the camera.
5. Depress the shutter button as you would to take a picture.
If the “ERR 99′ message only appears when one particular lens is
attached, then that lens should be examined by a service technician.
If you see the “ERR 99′ with a different Canon lens attached, then the
camera should be serviced.

Aug 31, 2008 | Canon EOS-20D Body only Digital Camera

1 Answer

Error 99 is my problem... any ideas on a fix?


This may help you, it is from Canon.


Thank you for contacting Canon product support. I'm sorry to hear that
your EOS is displaying an "ERR 99" message.

To isolate the cause of the issue, we suggest that you do the
following:

1. Turn off the camera.
2. Remove the lens, battery, and CF card.
3. Allow the camera to sit without power for approximately 20 minutes.
4. Insert a fully charged battery, and turn on the camera.

Does the "ERR 99" message appear? If it does, then the camera should
be serviced. If it does not, then please proceed to the next set of
steps:

1. Turn off the camera.
2. Insert the CF card.
3. Turn on the camera.
4. Format the CF card in the camera.

Does the "ERR 99" message appear? If so, then the CF card is the most
likely source of the issue. Try using a different card.

If the message does not appear, please complete the following steps:

1. Turn off the camera.
2. Clean the lens contacts by gently rubbing them with a pencil eraser
or soft cloth. Be careful that you do not let any debris fall into the
camera body.
3. Reattach your lens.
4. Turn on the camera.

If the "ERR 99" message only appears when one particular lens is
attached, then that lens should be examined by a service technician.

If you see the "ERR 99" with a different Canon lens attached, then the
camera should be serviced.

For factory service, forward your digital camera (remove the CF card
and battery) properly packaged and insured, with a letter describing the
difficulties. Be sure to include your name, address, telephone number,
and proof of warranty (if applicable). Send to the Canon Factory
Service Center at the following address:

Canon Factory Service Center
100 Jamesburg Road
Jamesburg, NJ 08831
Tel.# (732)521-7007

or

Canon Factory Service Center
15955 Alton Parkway
Irvine, CA 92618
Tel.# (949) 753-4200

Your equipment will be examined and you will be advised of the
findings.
The length of time for the repair will be dependent upon the nature of
the repair and availability of parts if needed. If the repair entails
something that is not covered in warranty you will be sent a written
estimate to the address that you have provided.

Thank you for choosing Canon.

Sincerely,

xxxx
Product Support Representative

Dec 26, 2011 | Canon EOS 400D / Rebel XTi Digital Camera

1 Answer

I HAVE A CANON EDS 20 D IT KEEPS CLICKING ERR


Try removing the batteries and wiping the connectors on the batteries and the connectors in the motordrive with a lens cloth. This worked for me. Sometimes the connectors get dirty and need to be cleaned for a complete connection. Hope this helps.

Apr 23, 2010 | Canon EOS-20D Body only Digital Camera

1 Answer

Error reading on screen on 1000e


Hello :

Here is what Canon said according some forums :

To isolate the cause of the issue, we suggest that you do the
following:

1. Turn off the camera.
2. Remove the lens, battery, and CF card.
3. Allow the camera to sit without power for approximately 20 minutes.
4. Insert a fully charged battery, and turn on the camera.

Does the "ERR 99" message appear? If it does, then the camera should
be serviced. If it does not, then please proceed to the next set of
steps:

1. Turn off the camera.
2. Insert the CF card.
3. Turn on the camera.
4. Format the CF card in the camera.

Does the "ERR 99" message appear? If so, then the CF card is the most likely source of the issue. Try using a different card.

If the message does not appear, please complete the following steps:

1. Turn off the camera.
2. Clean the lens contacts by gently rubbing them with a pencil eraser
or soft cloth. Be careful that you do not let any debris fall into the
camera body.
3. Reattach your lens.
4. Turn on the camera.

If the "ERR 99" message only appears when one particular lens is
attached, then that lens should be examined by a service technician.

If you see the "ERR 99" with a different Canon lens attached, then the
camera should be serviced.
I hope this will help .

please don't forget to rate !

Apr 06, 2010 | Canon EOS Digital Rebel XS / 1000D IS...

2 Answers

I keep getting error 99. I've cleaned the sensors with a new eraser; I've changed the battery and changed the memory card. If I take out the battery and put it back in, I can take a picture. If I pause for...


Hello:

Here is what Canon said :

To isolate the cause of the issue, we suggest that you do the
following:

1. Turn off the camera.
2. Remove the lens, battery, and CF card.
3. Allow the camera to sit without power for approximately 20 minutes.
4. Insert a fully charged battery, and turn on the camera.

Does the "ERR 99" message appear? If it does, then the camera should
be serviced. If it does not, then please proceed to the next set of
steps:

1. Turn off the camera.
2. Insert the CF card.
3. Turn on the camera.
4. Format the CF card in the camera.

Does the "ERR 99" message appear? If so, then the CF card is the most likely source of the issue. Try using a different card.

If the message does not appear, please complete the following steps:

1. Turn off the camera.
2. Clean the lens contacts by gently rubbing them with a pencil eraser
or soft cloth. Be careful that you do not let any debris fall into the
camera body.
3. Reattach your lens.
4. Turn on the camera.

If the "ERR 99" message only appears when one particular lens is
attached, then that lens should be examined by a service technician.

If you see the "ERR 99" with a different Canon lens attached, then the
camera should be serviced.

I hope this will help

please don't forget to rate !

Mar 11, 2010 | Canon EOS Digital Rebel XS / 1000D IS...

1 Answer

My canon eos rebel xti keeps showing error code 99



To isolate the cause of the issue, we suggest that you do the
following:

1. Turn off the camera.
2. Remove the lens, battery, and CF card.
3. Allow the camera to sit without power for approximately 20 minutes.
4. Insert a fully charged battery, and turn on the camera.

Does the "ERR 99" message appear? If it does, then the camera should
be serviced. If it does not, then please proceed to the next set of
steps:

1. Turn off the camera.
2. Insert the CF card.
3. Turn on the camera.
4. Format the CF card in the camera.

Does the "ERR 99" message appear? If so, then the CF card is the most
likely source of the issue. Try using a different card.

If the message does not appear, please complete the following steps:

1. Turn off the camera.
2. Clean the lens contacts by gently rubbing them with a pencil eraser
or soft cloth. Be careful that you do not let any debris fall into the
camera body.
3. Reattach your lens.
4. Turn on the camera.

If the "ERR 99" message only appears when one particular lens is
attached, then that lens should be examined by a service technician.

If you see the "ERR 99" with a different Canon lens attached, then the
camera should be serviced.

Sep 22, 2009 | Canon EOS 400D / Rebel XTi Digital Camera

2 Answers

I have a new Rebel xs kit, and after 20 shots, I got the err 99. I did all the above, that is from cleaning contacts to everything possible procedure mentioned in this forum. There are few things that I...


b10909f.gif

2364a9a.jpg

I can help you fix the BUSY Error or Error 99 of your Canon EOS Rebel XS.

Installation of this Canon EOS Rebel XS firmware version 1.06 update will solve these problems:
  1. Some cameras may exhibit a phenomenon in which the LCD monitor does not display, the shutter does not release, and the BUSY indication remains lit in the viewfinder.
  2. The message, "Err 99 Shooting is not possible. Turn the power switch to<OFF> and <ON> again or re-install the battery", appears on the camera's LCD monitor, and after the above operation is carried out,the LCD monitor displays in a language that is different from the actual language setting.
See the firmware instructions and download the firmware upgrade by following these Fixya Tips :

  1. Follow this link to download a pdf version of the firmware installation instruction guide.
  2. Follow this link to download the Windows Version of the Canon EOS Rebel XS / Canon EOS 1000D firmware version 1.06 update.
  3. Follow this link to download the MAC version of the Canon EOS Rebel XS / Canon EOS 1000D firmware version 1.06 update.
  4. Follow this link to download the Canon EOS Rebel XS / Canon EOS 1000D Instruction Manual.

I hope that helps.

Aug 26, 2009 | Canon EOS Digital Rebel XS / 1000D IS...

1 Answer

ERR 99


Err 99 usually means your lens contacts are dirty either on the lens itself or on the camera.

To isolate the cause of the issue, do the following: -
1. Turn off the camera.
2. Remove the lens, battery, and CF card.
3. Allow the camera to sit without power for approximately 20 minutes.
4. Insert only a fully charged battery, and turn on the camera.
5. Depress the shutter button as you would to take a picture.

Does the “ERR 99" message appear? If so, the camera may be faulty and requires a service. If it does not, then: -
1. Turn off the camera.
2. Insert the CF card.
3. Turn on the camera.
4. Format the CF card in the camera.
5. Depress the shutter button as you would to take a picture.

Does the “ERR 99" message appear? If so, then the CF card is faulty. Try a different card. If the message does not appear: -
1. Turn off the camera.
2. Clean the gold contacts on the lens by GENTLY rubbing them with a pencil eraser or soft cloth. Keeping the camera face pointing down, also clean the gold contacts on the camera, being careful that you do not let any debris fall into the camera body.
3. Reattach your lens.
4. Turn on the camera.
5. Depress the shutter button as you would to take a picture.

If the “ERR 99" message only appears when one particular lens is attached, then that lens should be examined by a service technician.
If you see the “ERR 99" with a different Canon lens attached, then the camera is faulty and should be serviced.

Apr 11, 2009 | Canon Rebel XT / EOS 350D Digital Camera

1 Answer

Canon eos 30 d is having err 99 problem after every five ok click


To isolate the cause of the issue, do the following: -

1. Turn off the camera.
2. Remove the lens, battery, and CF card.
3. Allow the camera to sit without power for approximately 20 minutes.
4. Insert only a fully charged battery, and turn on the camera.
5. Depress the shutter button as you would to take a picture.


Does the “ERR 99′ message appear? If so, the camera may be faulty and requires a service. If it does not, then: -

1. Turn off the camera.
2. Insert the CF card.
3. Turn on the camera.
4. Format the CF card in the camera.
5. Depress the shutter button as you would to take a picture.


Does the “ERR 99′ message appear? If so, then the CF card is faulty. Try a different card. If the message does not appear: -

1. Turn off the camera.
2. Clean the gold contacts on the lens by GENTLY rubbing them with a pencil eraser or soft cloth. Keeping the camera face pointing down, also clean the gold contacts on the camera, being careful that you do not let any debris fall into the camera body.
3. Reattach your lens.
4. Turn on the camera.
5. Depress the shutter button as you would to take a picture.
If the “ERR 99′ message only appears when one particular lens is attached, then that lens should be examined by a service technician.
If you see the “ERR 99′ with a different Canon lens attached, then the camera is faulty and should be serviced.

Dec 29, 2008 | Nikon D200 Digital Camera

Not finding what you are looking for?
Canon MF8180C Color Laser MFC Printer Logo

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

old marine
old marine

Level 3 Expert

2005 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...