Question about Garden

Open Question

How to replace the line on a Mculloch mt270 strimmer

On replacing the line on a mcculloch mt270 strimmer the line will not pay out.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

scrodamoon
  • 659 Answers

SOURCE: Strimmer Line

rotate the starter pulley by hand. You should feel the spring getting tight. Once the pulley is slightly tensioned, usually 5-10 turns, release the pulley and let is pull the string onto the pulley. You may have to add some tension to get all the rope to wind on the pulley.

Posted on Oct 04, 2008

  • 22 Answers

SOURCE: Strimmer line replacement

what model do you have?

Posted on Apr 03, 2009

moretons
  • 155 Answers

SOURCE: mcculloch strimmer/brush cutter - cuts out when throttle opened

Hi sounds like it could need a diaphram kit in the carby if it has mixture screws one markedl for low speed and one marked h for high speed you can try winding out the low speed screw a bit but if that does not work it will definatly need a kit.

Posted on Jul 25, 2009

MNfisherman
  • 11896 Answers

SOURCE: how to replace strimmer line to a McCuloch Cabrio

Try winding it the opposite direction. Make sure string is tight when winding. I usually keep one finger on the beginning piece of the string while I wind it up.

Posted on Sep 02, 2009

  • 477 Answers

SOURCE: replacing strimmer line on trueshopping hmlp4304ni1

Hi, on the side of the black spindle should be two tabs, push these in & the spindle cover should come off in your hands, Inside you will find a dual reel, one length of line needs to be fed in one way & the other the other way, making sure you have enough strimmer line free from either the slots or the hole on the side of the reel put this reel back on the spindle & pop on your black spindle cover, Job done.

Posted on Aug 17, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My McCulloch 250cxl strimmer wont prime, new bulb, cleaned carb, new fuel lines


switch fuel lines,the one with filter is carb,the one without is the primer

Jun 26, 2015 | McCulloch Garden

1 Answer

Mcculloch petrol strimmer


Agnes take of the cutting head again and see if it runs at full speed without it. If it does you have either put the head on too tight or it's the wrong head.

May 11, 2014 | Garden

1 Answer

I have a mculloch trim mac sl+ but it will only run on 3/4 choke, any ideas?


It can be a dirty carb, plugged filter or a bad fuel line.

Aug 31, 2013 | McCulloch Garden

2 Answers

Mcculloch strimmer/brush cutter - cuts out when throttle opened


Hi sounds like it could need a diaphram kit in the carby if it has mixture screws one markedl for low speed and one marked h for high speed you can try winding out the low speed screw a bit but if that does not work it will definatly need a kit.

Jul 25, 2009 | Garden

1 Answer

Primer bulb not filling


Yes, I think the gas cap may be clogged. The gas cap must be able to breath, otherwise this vacuum will occur. Try starting your trimmer and when it starts to choke out, loosen the gas cap. It should get air back in the tank, then and keep running. If this works, clear the hole in the gas cap, or purchase a new one.

Jim

May 03, 2009 | McCulloch 26cc Gas Blower Mcb3208

6 Answers

McCulloch Chain Saw Manual


Found all the mcculloch manuals you could ever want on mcculloch product information site. Its run by mcculloch an you put the product weather chainsaw or strimmer whatever an the type in the next collum an press download then print it off all very easy. My manual was in german so made up i found stumbled on this.

Jan 14, 2008 | McCulloch MC1275 Steam Vacuum

Not finding what you are looking for?
Garden Logo

Related Topics:

301 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2475 Answers

john h

Level 3 Expert

10993 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...