Question about Ryobi 15" Electric Factory Reconditioned Trimmer (ZRRY41002) - Factory Reconditioned

1 Answer

Ryobi gas trimmer stalls when lowering the revoutions

Ryobi 725r gas trimmer .I could use the carburator settings

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Do you have the right kmix fuel to addat start on choke let run tell it dies then pump the ball on half choke and chage the plug

Posted on May 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a diagram on how to connect the fuel lines back on a ryobi 725r trimmer


Typical fuel line routing is:

One line (the one with the fuel filter in the end of it) comes out of the fuel tank2.gif and goes to the bottom fitting on the carburator. The second line comes out of the tank and goes to the bottom fitting on the primer bulb. The third section of line goes from the top fitting on primer bulb to top fitting on the carburator. Hope this helped and best wishes.

Oct 01, 2009 | Garden

1 Answer

Putting fuel line on right on ryobi 725r 15'' 31cc weedeater


Typical fuel line routing is:

One line (the one with the fuel filter in the end of it) comes out of the fuel tank2.gif and goes to the bottom fitting on the carburator. The second line comes out of the tank and goes to the bottom fitting on the primer bulb. The third section of line goes from the top fitting on primer bulb to top fitting on the carburator. Hope this helped and best wishes.

Sep 08, 2009 | Ryobi 30 Cubic Centimeter Curved Shaft Gas...

1 Answer

725r trimmer


You can buy new Line to re-spool on your existing head

Aug 17, 2009 | Ryobi 30 Cubic Centimeter Curved Shaft Gas...

1 Answer

Ryobi 720r trimmer starts ok but stalls when the


The carburator needs to be adjusted a little, thin our your mixture screw when the trimmer is warmed up and idling. Well how do you get it to idle? I usually have to play with the choke lever with the throttle wide open going from choke to partial choke as needed to keep it running. Adjusting can be tricky, you need a small screwdriver. Screw all the way in then back out 3 to 3.5 turns. this should get you close. Adjust idle as needed.

Jul 05, 2009 | Garden

2 Answers

RYOBI 725R FUEL LINE DIAGRAM


I just rebuilt my 725r. I don't have a diagram but I can explain it. There are two lines coming out of the fuel tank. The line closest to the rear is the fuel feed and has the in-tank filter (these are available for replacement). This line goes through the lower case hole of the air filter housing and attaches to the bottom of the carburetor. The line toward the front of the tank attaches to the longer/lower fitting the primer bulb and is the return. The line coming off the shorter/upper fitting of the primer bulb goes through the upper hole of the air filter housing and attaches to the top of the carburetor.

FYI also, the forward carburetor screw is the low idle adjustment & the rear, the high-speed mixture. The original oil mixture spec called for 32:1

Jun 13, 2009 | Ryobi 15" Electric Factory Reconditioned...

1 Answer

Replacing Drive Shaft for a Ryobi 725r


The lower flex shaft should cost around $40, unless you order it online and have to pay shipping. You should be able to get one from your local MTD dealer. (Ryobi is owned by MTD)

May 25, 2009 | Ryobi Garden

2 Answers

The pull rope broke on my ryobi 705r/725r gas trimmer. I have all the screws off but it seems to be held on by the center shaft that spins. What do I do now?


I have the same issue of clutch removal on a Ryobi 725r. Actually the clutch finally died after many years of use.
Instead of using a screwdriver to hold the piston I recommend using a piece of clothesline rope. It will be easier on the internal components and won't scratch up the cylinder walls or piston. Just be sure to leave a small amount hanging out of the spark plug hole so you can pull it out afterward.

Apr 15, 2009 | Garden

4 Answers

Ryobi 2 cycle gas trimmer 705r/725r


The gas nipple that come out I have...whats goes in the other hole?

Aug 28, 2008 | Ryobi Garden

4 Answers

Ryobi 725r 31cc


Ryobi is Japanese for "Piece of ****" My suggestion is to throw it out!
My 767r has had fuel line and carb trouble from day one. I'll never buy another Ryobi or Craftsman tool again.

Jun 13, 2008 | Ryobi 15" Electric Factory Reconditioned...

Not finding what you are looking for?
Ryobi 15" Electric Factory Reconditioned Trimmer (ZRRY41002) - Factory Reconditioned Logo

Related Topics:

765 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ryobi Garden Experts

Nick Olsen

Level 2 Expert

183 Answers

Rexter1

Level 2 Expert

40 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Are you a Ryobi Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...