Question about Mitsubishi WS-65807 65" Rear Projection Television

1 Answer

Scrolling lines I have a 65" mitsubishi tv, WS-65807. i bought this tv new in 2000, i had to have the convergence ic's resoldered about 6 months ago, now i have a new problem. the picture has scrolling horizontal lines when i use the hi def component input, the problem goes away when i disconnect the cable tv jack. Any ideas as to what is wrong. I also had the tv calibrated by an ISF tech in 2001. Awesome picture when it is not messing up.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 87 Answers
Re: Scrolling lines

Try using a DVD though the component input (need a 480P out ). If the pix si ok I wouldsuspect the cable box. If the problem is still there I would suspect a video switching IC or a Leaky regulator.

Posted on Nov 05, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Tv screen is warped on edges. what to do?

The tv have a problems known as a convergence problems,it dead.Tv have colors lines R,G,B mis alignment,have colors shadows pictures or 3D pictures look alike.The tv convergence board 2 STK convergence ICS and some or all it resistors are dead.These parts on the tv convergence board,must be replaced to solved the tv picture convergence problems.The shop,will cost u like $300-350 for parts and labors.

Oct 28, 2010 | Mitsubishi WS-65807 65" Rear Projection...

1 Answer

For past 6 Months The scren was bowing Horizontally and now it has sever ghosting.. What to do this TV is about 8 years old Model Number WS-65807

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.
This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.
You can get a repair kit with parts and instructions from

Sep 24, 2010 | Mitsubishi WS-65807 65" Rear Projection...

1 Answer


It needs to be repaired by having the convergence ICs replaced or resoldered (if intermittent).

Parts are STK 392-570. Be sure to use thermal paste on the ICs.

Jul 02, 2010 | Mitsubishi WS-65809 65" Rear Projection...

2 Answers

Blue and red overlap shadowing

convergence ic's are your culprit. they are responsible for aligning the 3 colors your tv projects onto your screen..

Mar 15, 2009 | Mitsubishi WS-65807 65" Rear Projection...

1 Answer

Mitsubishi WS-65807 blinks '22'

yes the convergence Ics are what cause the two picos to be open they are both 5 amp picos. You can get the picos, the convergence ICs and the factory service manual for your model at the following link.your model is known as the V17 chassis for service manuals and you should require two STK392-570 Convergence ICs. Heres the link they provide free instalation instructions.

Oct 02, 2008 | Mitsubishi WS-65807 65" Rear Projection...

1 Answer

Mitsubishi WS-65807 blinks '22'

I replaced the pico fuses and the convergence IC's. fuses poped right away code 22 . Further inspection of the board showed the coolant had leaked out of the center projector and fried the board. Not willing to pay $300. Passed it on to someone else

Oct 01, 2008 | Mitsubishi WS-65907 65" Rear Projection...

1 Answer

Blue bloom/out of focus

convergence ic going. you may also want to check some caps;

replace DM

Jan 18, 2008 | Mitsubishi WS-65807 65" Rear Projection...

1 Answer

Mitsubishi WS-65807 problems

You need the two convergence IC's replaced part# STK392-570. About a $300-$400 repair.

Aug 23, 2007 | Mitsubishi WS-65807 65" Rear Projection...

1 Answer

Vertical lines across screen

first bad link !!! tell me if you get these lines away when you do little hits on the side of the tv , if so that mean you have bad soldering pin and need resoldering regards please don't forget to rate thx

May 03, 2007 | Mitsubishi WS-65807 65" Rear Projection...

Not finding what you are looking for?

Open Questions:

See all Mitsubishi WS-65807 65" Rear Projection Television Questions

Mitsubishi WS-65807 65" Rear Projection Television Logo

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Projection Televisions Experts

matt martin
matt martin

Level 3 Expert

1187 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

The Knight
The Knight

Level 3 Expert

66552 Answers

Are you a Mitsubishi Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides