Question about Viper RCVGC022 Remote Control

2 Answers

Viper auto alarm stuck in valet mode

How do i get my viper auto alarm out of valet mode and back to alarm mode ?

Posted by on

  • Doctor C Oct 16, 2007

    posted this request yesterday.



     



    this a an extremely simple problem for a viper auto alarm expert, yet no apparent solution as of 10:30 am.



     



    is this site worth my time to re-visit ?  (again)

  • Doctor C Oct 17, 2007

    apparently still no solution as of wednesday, oct 17, 2007 as of 10:28.

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

U can open the drivers door if u have a 2 key remote just press lock aux lock again pretty fast and u should be great.

Posted on Dec 22, 2008

  • tici39 Mar 14, 2011

    I have a Viper 0890 car alarm in valet mode...steady blue light. Lock-Aux-Lock return the system to normal operation. Thanks.

    Tgatar

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Doctor C,

I to have suffered the trial and tribulations of the viper car alarm experience and am happy to pass on my knowledge.  I found this answer online after googling "viper valet mode"

 

"The LED is solid now, correct? This means the unit is in Valet mode. To get out of it, turn the key to the "on" position then back off, and just press your black program button hidden under the dash.  The installer should have shown you where they installed the black program button."

 

Good luck

Scott

 

Good Luck

Posted on Oct 19, 2007

  • 1 more comment 
  • vg750li Jul 13, 2010

    Thank you very much I took my truck to the shop but they left my alarm in valet mode. This was very helpful to me and I just wanted to say thanks.

  • agcooke60 Jul 11, 2011

    Thanks works perfect!

  • kath2708
    kath2708 Apr 04, 2012

    Thank you Scott! It is the simple things in life and this did the trick!

    Kath

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Which one is valet button on the viper 474


No key in ignition, door wide open, press lock-unlock-lock within one second. That will valet the alarm and the led will light up steady. Follow same instructions to remove alarm from valet mode.

Oct 04, 2010 | Viper Security and Remote Start System...

1 Answer

The alarm is on a 1996 f150 the alarm will not chirp the led on truck is solid it isnt blinking and it is a 5701 viper


Your alarm got put into valet mode some how
.It's easy to reverse out of it back to normal. First look for a small black push button under the dash somewhere. It's called a valet button. Here are the steps.
1. open door
2.turn key on then off
3.then within 10 seconds hit that valet button once(your alarm light should be off. Tell you arm it again. Then it will blink)
Hope this helps

Aug 18, 2010 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

1 Answer

How do I get my viper alarm from silent mode to chirp mode?


if its in valet mode to get it out
open door put key in IGN to the ON position push the valet (black) button one time then turn key off and remove
;)

Jun 24, 2010 | Viper Security and Remote Start System...

1 Answer

So I have a viper alarm system in my car and awhile ago the remote got wet, so in order to be able to start my car i had to disable the alarm by turning the ignition on and pressing that eraser like...


You have to turn off your ignition and immediately press that 'eraser like button'(valet switch) for a second and release it. Alarm will then come out of valet mode and your remote should work, if it's good.

Jun 01, 2010 | DEI Valet Keyless Entry System

1 Answer

I have a Viper 470v alarm and the keypad does everything it supposed to do as far as starting the truck locking and unlocking BUT it doesn't beep anymore and the screen doesn't reflect my status. It stays...


Is the red or blue light (LED)on the dash lit up solid? If it is then the alarm is in valet mode. 2 ways to take it out of valet. 1) open a door and press lock, unlock then lock again on your Viper remote. 2) turn the ignition on then off and press your valet/override button. The LED should go out and the beeps and status should come back. BTW you can also put the Viper into valet mode using the 2 methods above.

Feb 23, 2010 | Directed Electronics 479V Remote Gen 2...

1 Answer

Viper car battery went dead now alarm light on


you are in valet mode.
find valet switch under dash or driver kick panel.
turn key on
then push the valet switch for a few seconds.
light should go out and then function properly again.

Jan 16, 2010 | Vehicle Parts & Accessories

2 Answers

Disable viper alarm


Yes the best way is disarm the alarm and put in a Valet Mode
To activate the Valet Mode do the following:

There is a push button or toggle switch to disable the alarm (to engage the valet mode). Without knowing where this
switch is you won't be able to disconnect the alarm.

1. Put the key in the ignition and turn it to the "on" position.
2. Flip the toggle or hold the push button for at least 5 seconds.
3. The LED. light will stay solid on.
4. Turn the ignition off
5. Release the push button. If you have a toggle leave it alone in step 2

Jan 07, 2010 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

3 Answers

The alarm doesn't chirp and no flash of my headlights anymore. Also the blue light stays on the little receiver/antenna on the windshield wheather it is locked or not. What is the problem?


sounds like the alarm went into valet mode. that's usually what a solid blue light means on most viper alarms. check your owners manual on how to take the alarm out of valet mode. with the 5701 alarm its usually done with the remote. hope this helps

Aug 04, 2009 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

1 Answer

I cant disarm my alarm


Get inside the car, turn the key to the on position, the alarm is going to sound so do not panic when the alarm sounds press the valet button one time and the alarm should stop. To place the alarm in valet mode cycle the key with the door open on then off then press the valet button one time and the alarm should go into valet mode meaning the alarm light will be on steady.

Feb 03, 2009 | Viper Security and Remote Start System...

Not finding what you are looking for?
Viper RCVGC022 Remote Control Logo

13,410 people viewed this question

Ask a Question

Usually answered in minutes!

Top Viper Televison & Video Experts

Hjalmer Lamminen
Hjalmer Lamminen

Level 3 Expert

552 Answers

Paul Bade

Level 3 Expert

1626 Answers

richie46

Level 3 Expert

12962 Answers

Are you a Viper Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...