Question about Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

1 Answer

Hoover steam vac ls

  • I bought this product from K-mart 2 days ago. I went to put it together and it is missing pieces. The pieces i am missing are the ones that go in the hose box. I didn't take it back to K-mart because it was the last one and this is the one i wanted

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,673 Answers

Contact you nearest Hoover shop and they can order what you need. Hoover will cover it under warranty. You will need proof of purchase, model and serial numbers.

Posted on Jan 10, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Bosch pmf 190e just stopped working.fuse ok lead ok

I have fixed my Bosch PMF 190E which had this problem.
Take the casing apart using a normal flat head screwdriver. Wiggle the two halves and the top piece will come away. There are two more screws inside to remove which are holding the power flex cable in place. Now you can gently remove the coil and board from the lower casing. Then pull out the inside coil from the front section (they easily just slip in and out)
Now if you look carefully there are 4 tiny copper wires connecting the coil to the power. It is very likely that one of these has snapped as they are very thin and there is a lot of vibration in there when the machine is running. Note: Do look carefully as I almost missed the snapped wire. So I just bought a soldering iron and some solder for £5 and soldered them back together. This was the first time I had ever soldered anything so that shows that this is not difficult!!
I then put it all back together and it worked again.
I was very close to buying a new one so I am happy that I gave this a go. I'm sure most people can do this just as easily. Give it a go before buying a new one.

Feb 08, 2014 | Bosch Pmf 180 E Multifunctional All...

1 Answer

My dyson dc24 had no suction so a friend take it apart supposely put it back together but I notice there was a metal piece that was just attached at one spot so after a few months the roller brush wasnt...

Hi Debra,

Issues with performance are usually very easy to resolve, and shouldn't require the machine to be dismantled. Unfortunately if the machine has now been disassembled to this extent, the 5-year guarantee will now have been voided.

I would encourage you to contact us directly so we can determine if your machine is missing any parts, and discuss your options for getting your vacuum up and running again. You can reach the Dyson customer Helpline by calling 0800 298 0298 (UK), or 1-866-693-9766 (US)

Best wishes,

Dyson Online Customer Support

Sep 20, 2013 | Dyson Ball DC24 Bagless Upright Vacuum

1 Answer

My e-2 vacuum runs very loud and smell like it's burning.

You may have damaged a bearing or bearing housing and that could be causing the motor armature and field to rub together which in turn causes the motor to draw a significantly increased current to overcome the friction. It could be a simple fix if it is a bearing but if it is the housing then it is likely toast. I used to repair motors years ago and the cost then was not bad. However if the motor is heat damaged, as happened to my power rack last year, it was cheaper to buy a new one than replace the motor. A burned out motor is not worth repairing these days.

Dec 19, 2017 | Rainbow E series Canister Wet/Dry Vacuum

1 Answer

I need to reassemble my rainbow e series electrified hose handle

Yes, it is a ground wire. When you put it back together, make sure that the two halves of the hose handle are holding the wire up against the metal. I just had one apart the other day for the first time and if I recall correctly, the wire goes near the center for reassembly. Hope this helps!

Mar 15, 2009 | Rainbow E series Canister Wet/Dry Vacuum

7 Answers

Red power switch

you either have a bad switch or your handle has come loose. in several cases with this vac the handle comes loose and the vac will start acting funny. if you look at the back of the handle and start looking down the first screw you see make sure its tight.

Sep 17, 2008 | Bissell 5770 Healthy Home Bagless Upright...

1 Answer

Kirby 5 Model G5D

is there a re set button on a Kirby. Used the vacuum 2 weeks ago, worked just fine. Went to use it today and it won't start. Any ideas?

Jul 31, 2008 | Vacuums

1 Answer

Bissell laminate floor cleaner wet vac and flips to dry vac

You just need to replace the cap and valve part # 2036919, You should be able to order the part thru, or they will tell you who you can call close to you.

Dec 06, 2007 | Vacuums

Not finding what you are looking for?
Hoover SteamVac F5914-900 SpinScrub Upright Vacuum Logo

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

Jim Parker
Jim Parker

Level 3 Expert

1041 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

Are you a Hoover Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides