Question about Maytag MAH2400A Front Load Washer

3 Answers

MAH2400a not filling with water

I've tried this with cold, warm and hot water. The water will start filling for maybe 5 seconds and then stops. Think this is one of the 3 sensors on the top rear of the machine? I've replaced the main board to no avail. Thanks.

Posted by on

  • jamesb221 May 14, 2009

    Would you happen to have the factory listed name for this part (assy-sensor?) or part number? Thanks very much!

  • jamesb221 May 15, 2009

    MAH2400a



    Thanks.

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Maytag Master
  • 75,051 Answers

There are level sensors, I suspect one is defective, replace them.

Posted on May 16, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,136 Answers

Hi, Can I get your model # so that I can see ezactly what machine you have? It sounds like the sensors but, I would like to look into it.

Thanks,
Vic

Posted on May 15, 2009

  • Victor
    Victor May 15, 2009

    I could have you an answer very quick.

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 952 Answers

If you have already replaced the main board then Its probably bad sensor. Have the sensors checked or have it replaced. I hope this helps. Have a good one.

Posted on May 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washing machine stopping and starting when filling


Sounds like maybe a bad water inlet valve? timer may have isses as well? have u tried running it in hot water only and cold water only cycle? see if one line is bad in ur inlet valve?

Dec 16, 2014 | Washing Machines

1 Answer

Hot/cold cycle stops before filling up


Your washer has a set amount of time to fill. If the flow is low and the time runs out, then all you will get is the amount of water that was able to fill. Check your lines to be sure that they all fully opened.

Aug 12, 2012 | Admiral 32 cu. ft. Washer

1 Answer

Whirlpool model WTW5310VQO


i've found problems with the temp. switch on this washer part number W10184148 and it's around 40 dollars,also on the rinse cycle the washer only uses cold water.what happens when you use just the hot?i had a lady that her water would start to fill and then the water would stop and the pipes in the house would start making a banging sound.if you order the part from http://www.repairclinic.com/PartDetail/Switch/W10184148/1468990 repair clinic and if this isn't your problem which i think it is from how you discribe it you can send the part back and get your money back for up to a year.good luck with your washer and next time you buy something and it doesn't work right get right on it

Mar 14, 2012 | Whirlpool Ultimate Care II LSQ9549L Top...

2 Answers

When set on delicate cold/cold water, it starts to fill with cold but switches to hot water after a few seconds


Sounds like you've got the hoses switched, and the cold water you're feeling is just what is in the hot water lines until the lines get purged. Try filling on the hot setting and see if cold or hot comes out; my guess is you'll get cold water on the hot setting.

Nov 20, 2011 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

There is a hot water valve & a cold water valve on the Dexter T300 machines but it is a 2 coil valve. does the hot water valve supply only hot water or does one side provide water to perhaps the...


supplies hot water when needed, cold water when needed. and then warm water when needed. so the second coil is for warm water. it basically mixes the hot and cold water.

Mar 17, 2011 | Washing Machines

1 Answer

Hi, my washing machine isn't working in cold/cold mode but will work in hot/cold and warm/cold. Meaning that water will not come out at all. I even started it in warm/cold and tried to switch it over to...


My bet is that your cold water screen is plugged...

If your washing machine will not fill, only hot or cold will fill or is slow to fill then read these tips. I have covered many of the things that can happen in these tips…


Washing Machine Problems No Water

Washing Machine Fix Washing Machine No Water

heatman101

Aug 31, 2010 | Frigidaire Washing Machines

1 Answer

Washer will not fill up with hot or warm settings, only cold.


kenmore washer hot or cold fills ok but will not fill with warm but only cold water

Mar 15, 2009 | Kenmore Washing Machines

2 Answers

I have the washer on cold water, but it runs warm, stops, trickles, then comes out warm again, stops, trickles, then warm again ect.On the rinse cycle it will only trickle out.


The water fill valve - The water fill valve is a mechanical and electrical part, the coils on the valve need electricity to mechanically open the valve to allow the water to flow into the washer....myth....the washer pumps water into itself...no, it does not. The fill valve opens and the house water pressure pushes the water into the washing machine.
No cold water or no hot water - The fill valve has two coils, one for the hot water and one for the cold water. It is possible that one of the coils can fail and you loose that filling ability. If the cold water coil quits, the hot will still work and during warm fill you will get hot water only and during a cold fill you will get no water at all. If the hot coils quits, you will still have cold water fill, cold water only on a warm setting and no water on a hot fill setting. You can No cold water or no hot water - The fill valve has two coils, one for the hot water and one for the cold water. It is possible that one of the coils can fail and you loose that filling ability. If the cold water coil quits, the hot will still work and during warm fill you will get hot water only and during a cold fill you will get no water at all. If the hot coils quits, you will still have cold water fill, cold water only on a warm setting and no water on a hot fill setting. You can test a fill valve live for 120 volts, power to a fill valve coil and no fill = a bad fill valve. You can also test the coils for continuity, no continuity = a bad fill valve. Some Maytag washers have a fuse in the fill valve circuit, if this fuse let go the washer will not fill. Fill valves can also from time to time stick open and not stop filling. If you have to shut off the fill valves to stop the water from filling in the washer, you have a bad fill valve and you will have to replace it.

Mar 03, 2009 | Washing Machines

2 Answers

Cold water will not stop filling during rinse


while the unit is filling in the warm cycle. reach behind and shut off the hot water tap.I bet the water flow stops filling, if so, you would need to change the inlet valve on the machine. You see, in warm, if the cold is not filling, you still hear the hot filling and the unit will advance. The rinse cycles are mostly "cold" only. if the valve is not opening it will not allow it to advance from the rinse section on the board.

Good luck!

Feb 16, 2009 | Maytag Neptune MAH5500B Front Load Washer

Not finding what you are looking for?
Maytag MAH2400A Front Load Washer Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

587 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...