What is the partial product for 77 times 30 - Computers & Internet

Assuming you mean "forty-one" and "seventy-six", the partial products are 2800, 240, 70, and 6. Adding those together gives 3116, which is 41*76.

Today's water heaters have more insulation and are larger.

Reliance does not have a water heater 20 x 38.
http://www.reliancewaterheaters.com/lit/spec/electric/R606E0312.pdf

I checked several manufacturers.

American Water Heater has 18 x 38-1/2"
Model #E62-30H-045DV
Shipping weight 77 lbs, but I don't know who sells it.
http://www.americanwaterheater.com/products/pdf/NRESS00308.pdf

Whirlpool from Lowes has a 30 gallon
18" x 45"

If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

Sounds like the system is either over charged with freon or under sized. Call the same people back out ask for a supervisor to come out and check out the system any other company will charge you.

Perform a partial reset Perform a partial reset to restore the product settings to the default values.

1. Write down any fax numbers and country/region and language settings stored in the product memory.
CAUTION: A partial reset might remove all speed dials and other settings from the product memory.
2. Disconnect the power cord from the rear of the product.
3. Press and hold the # and 3 buttons at the same time while plugging the power cord into the rear of the product.
4. Release the buttons after 30 seconds or when Part NVM Reset displays on the control panel.
5. If the product does not turn on automatically, press the Power button ( ) to turn it on.
6. Press OK to continue the current task.


Next solution

Dowload the Firmware fix on this line. make sure it's connected over the usb cable.


http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=2093&lc=en&cc=us&dlc=en&sw_lang=&product=3737195#N260



Critical Update to Prevent an Error State When Connecting Your Printer to a Network
2009-07-16 , Version:1.0, 789.02k
This update will prevent your printer from entering an error state and displaying an error message on the Front Panel Display when connecting to a network.

That is a ink system failure error. followed the Ts steps on the link. If still unresolved then you might need to change printheads.


http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01458034&cc=us&lc=en&dlc=en&product=3737195&tmp_track_link=ot_search#N998

additional info below how to reset



Perform a partial reset Perform a partial reset to restore the product settings to the default values.

1. Write down any fax numbers and country/region and language settings stored in the product memory.
CAUTION: A partial reset might remove all speed dials and other settings from the product memory.
2. Disconnect the power cord from the rear of the product.
3. Press and hold the # and 3 buttons at the same time while plugging the power cord into the rear of the product.
4. Release the buttons after 30 seconds or when Part NVM Reset displays on the control panel.
5. If the product does not turn on automatically, press the Power button ( ) to turn it on.
6. Press OK to continue the current task.

Perform a partial reset Perform a partial reset to restore the product settings to the default values.

1. Write down any fax numbers and country/region and language settings stored in the product memory.
   CAUTION: A partial reset might remove all speed dials and other settings from the product memory.
2. Disconnect the power cord from the rear of the product.
3. Press and hold the # and 3 buttons at the same time while plugging the power cord into the rear of the product.
4. Release the buttons after 30 seconds or when Part NVM Reset displays on the control panel.
5. If the product does not turn on automatically, press the Power button ( ) to turn it on.
6. Press OK to continue the current task.

• If these steps resolved the issue , you do not need to continue troubleshooting.
• If the issue persists , continue to the next solution.

Next solution

Dowload the Firmware fix on this line. make sure it's connected over the usb cable.

http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-77368-1&lc=en&dlc=en&cc=us&os=228&product=3795406&sw_lang=&key=null&site=null

I had a 77 Power Wagon that did the same thing all the time. It turned out to be the coil..

Click on start then go to devices and printers or printers depending on your operating system. look for the c309 icon - right click and choose properties - properties window will come up- click on the advance tab and in the middle section choose "print directly to printer".



another solution is to do a partial rest on the printer.



Perform a partial reset Perform a partial reset to restore the product settings to the default values.

1. Write down any fax numbers and country/region and language settings stored in the product memory.
CAUTION: A partial reset might remove all speed dials and other settings from the product memory.
2. Disconnect the power cord from the rear of the product.
3. Press and hold the # and 3 buttons at the same time while plugging the power cord into the rear of the product.
4. Release the buttons after 30 seconds or when Part NVM Reset displays on the control panel.
5. If the product does not turn on automatically, press the Power button ( ) to turn it on.
6. Press OK to continue the current task.