Question about IBM Infoprint 40 Laser Printer

1 Answer

Infoprint 40 with 454 Fuser error

Sometimes the printer works well during a long time (8hours) without errors. But normally after 1 hour stop with the error.

Posted by on

  • Frank Zhang
    Frank Zhang May 11, 2010

    how long the fuser you used, and do you know how many pages printing?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 123 Answers

Sure.. the 654 is an MCU communication error, so the MCU card is
probably bad (it's located near the front left side of the printer,
under the operator panel). If the MCU is good, the controller card is
the 2nd most likely suspect.

The least expensive way to fix the problem would be to purchase a used
Infoprint 21 with a bad fuser (one that is posting a 454 error), and
put your good fuser in that IP 21. Then make sure that the controller
card in your IP 21 is good by swapping it in the operational printer,
and sell the good controller card -- you might come out a few dollars
ahead in the end.

Posted on May 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Infoprint 1145 ''915 Service Fan Error''


915 Fan Error Fuser fan failure


1
+24VDC CHECK
Measure the voltage at P/J456-1 and FG on the I/O PWB.
Is there +24VDC between J456-1 and FG?
Yes: Replace the “Fuser Fan”
No: Use the Block Diagrams in the printer service manual to troubleshoot a loss of +24VDC

2
The following printer FRUs and areas are associated with this
specific problem. One or more of these FRUs or areas may
have failed partially or completely. If you cannot isolate this
problem using the steps in this Service Check, replace each
FRU or troubleshoot each area listed below, one at a time, until
you isolate and solve the problem.
• Wiring and connectors linking the FRUs
• I/O PWB


Mar 23, 2010 | IBM Infoprint 1145 Laser Printer

1 Answer

IBM Infoprint 1532 giving error code 922.14 -service fuser error


There is a heater control problem in the fuser.
The fuser is the assembly of heated rollers in the rear of the device.
The most likely cause is either a blown heater element, or perhaps a faulty temperature sensor.
Usually we fit an exchange fuser assemblt to fix this.

Feb 04, 2010 | IBM Infoprint 1532 Laser Printer

1 Answer

925 service fuser error


A 925 Fuser Error indicates that the wrong fuser lamp or the incorrect fuser assembly is installed.
  1. If this error appears shortly after the fuser unit in the printer is replaced, put the old fuser unit back in.
    If the error message goes away with the old fuser unit, please check that the new fuser unit is the correct one for this printer model.
  2. If the printer has not recently had its fuser replaced, plug the printer directly into a wall outlet. Surge protectors and power strips can sometimes regulate the voltage to a fault for the printer. If the printer is already on a wall outlet, plugging the printer into a different outlet may solve the problem. Keep in mind that there is no need to have the printer connected to a computer during testing for a fuser error as any pages to test the functionality of the printer can be processed internally.
  3. If you have tried the printer on other wall outlets and the 925 Fuser Error still appears, the printer will require service to clear the message.

Jan 12, 2010 | IBM Infoprint 1352 Laser Printer

2 Answers

Receiving an error 920.06 Service fuser error


920 .06 Fuser is not increasing in temperature even though the lamp has been on for an extended time. Fuser page count between 0 and 99,999. • Fuser is not receiving AC power. • Poor supply line voltage.

Jun 16, 2009 | IBM Infoprint 1532n Laser Printer

1 Answer

Infoprint 1634 repeatedly jams


It may be time to replace the Fuser.

There is no certified way to repair a Fuser with purchasable parts, the assembly it self must be replaced.

May 22, 2009 | IBM Infoprint 1634 Laser Printer

1 Answer

922 Server fuser error


922 fuser errors is a bad fuser - you might try turning off printer - holding the select and return button down at the same time - turn on printer - HOLD buttons until it starts inting (about 15 sec) and the arrow over to print test pages - if the error doesn't return - repeat a few times.... this may by pass the error.. then power off - ON and see if problem is gone. replace fuser if not

Apr 08, 2009 | IBM Infoprint 1120 Laser Printer

1 Answer

Fuser error on my ibm infoprint color 1464


The error is Fuser cam position not found. Have you tried reseating the fuser? Does the fuser make any loud sounds? Based on the error message, it could either be the fuser, or the system board.

Apr 08, 2009 | IBM Infoprint 1116 Laser Printer

1 Answer

IBM InfoPrint 1612 Repeatedly erroring - Paper Jam


Check the FUSER, I think your exit sensor is bad.
If you open the rear door, look inside where the paper starts to come out of the printer, you should see a small lever that triggers the PAPER EXIT sensor. It might be hard to see. If it is not broken, you need a new FUSER.

Mar 18, 2009 | IBM Infoprint 1612 Laser Printer

1 Answer

IBM Infoprint 21- 651 HW error


Look in Printer Manual (usually in the back) for error codes.

Try cycling power including unplugging AC cord from printer for 1/2 hour.

Apr 25, 2008 | IBM Infoprint 21 Laser Printer

Not finding what you are looking for?
IBM Infoprint 40 Laser Printer Logo

Related Topics:

344 people viewed this question

Ask a Question

Usually answered in minutes!

Top IBM Office Equipment & Supplies Experts

James Cagle
James Cagle

Level 2 Expert

453 Answers

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

Jim Keysor

Level 2 Expert

329 Answers

Are you an IBM Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...