Question about Proform CrossTrainer Treadmill

1 Answer

The belt on my ProForm Crosstrainer treadmill stops while using i

It will work for awhile but it will stop moving suddenly while using it. I have tried tightening it but this doesn't seem to work. The sudden stop of the belt is quite dangerous and I am afraid to use my treadmill.

Posted by on

  • Anonymous Mar 28, 2014

    I have proform 585TL some time it works good but some time it suddenly stop while I am using.It fuse drip out.any one could like to help me. So I rest the tripper and it works some time some repeat the same problem

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Sometimes the tread needs to be lubricated. This was the case with ours. You can get a lubrication kit at ****'s Sporting Goods or other larger sport stores and it will instruct you on how to do it.

Posted on Jan 26, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sudden Stoppage of my Treadmill


see the video and fix it. Lube too the rollers bearing front and rear+test the drive belt motor and replace if necessary. tight a little.
God bless you

Jun 15, 2013 | Proform Exercise & Fitness

1 Answer

Proform 350s crosstrainer treadmill; surges 3 MPH to 4MPH


Walking Belt is Worn: The only certain way to test for a worn walking belt is to take a DC amp draw (if you have a DC treadmill) or an AC draw (for AC). Trying to look at the belt or a feel test is highly unreliable. Better tests, if you lack a DC ammeter (they are expensive for a good one), are a coast test or an incline test. The coast test is to get on the treadmill as the lowest incline setting and walk on the treadmill at 3 MPH. Pull the safety key and it should take you 2-3 full steps to stop (this is a general rule…some like a few Tunturi models stop on a dime even with a healthy belt but for most models, this tests works well upon). Fewer steps indicate high friction. The incline test is to put the treadmill at max incline and walk on it at 3 MPH. If the treadmill operates normally at max incline but bogs down at minimum incline, replace the walking belt. Gravity takes over for the drive system eliminating much of the friction problem. On some heavily worn walking belts, this test will not eliminate the problem. Go to your local hard ware store and purchase silicone spray. Apply Lubricant by lift one side of the running belt spray contents length wise starting at motor shroud to the back end repeat this process on the other side. If this unit bogs down again then you will have replace the running belt and possibly the deck

May 27, 2010 | Proform CrossTrainer Treadmill

1 Answer

Belt skips


take the cover off, if the front drive roller continues to turn when the running belt stops, tension the running belt by using the rear adjustment screws. One full turn on each side should do it. If the front roller stops turning but the motor doesn't, tension the drive belt by adjusting the motor back.

May 26, 2010 | Proform 760 CrossTrainer Treadmill

1 Answer

Treadmill starts instantly, no belt ramp up


HAS A SHORTED MOTOR CONTROL BOARD NEED TO BE REPLACED.
GO TO iconfitness.com then to customer service then parts repalcement

Feb 21, 2010 | Proform CrossTrainer Treadmill

1 Answer

Belt stops and starts


look for a tension knob it will tighten the belt unless the belt is really wore out and may need replaced

Jan 06, 2010 | Proform 760 CrossTrainer Treadmill

2 Answers

My Proform 650v treadmill stop when running after couple of miles


Most likely a bad drive belt. Take the cover off the motor area. If you see black dust near the left side of the motor, replace the drive belt.

Oct 29, 2009 | Proform CrossTrainer Treadmill

1 Answer

Trouble shooting


Your belt may need adjustment. to tighten you need to use the allen key (supplied with the unit)

Sep 30, 2009 | Proform CrossTrainer Treadmill

1 Answer

PROFORM RUNS BUT WHEN I STEP ON IT EITHER SLOWS DOWN OR STOPS MOVING AT ALL


Belt needs tensioning up on its adjusters or the motor drive gear has come loose and needs tightening back up.

Jul 31, 2009 | Proform CrossTrainer Treadmill

1 Answer

Treadmil stops or slows down upon walking.


Check both belts to be sure they are adjusted and not slipping.Check the underside of the walk belt to see if it feels frayed in the center as compared to the edges, the center always wears more than the edges a really worn belt must be replaced. if it is nor worn there is a wax lubricant for proform treadmills that can be purchased at retail stores that sell treadmills.Sears, dicks sporting goods and also treadmilldoctor.com are good places to buy it.

Jul 30, 2009 | Proform CrossTrainer Treadmill

Not finding what you are looking for?
Proform CrossTrainer Treadmill Logo

Related Topics:

1,721 people viewed this question

Ask a Question

Usually answered in minutes!

Top Proform Exercise & Fitness Experts

Matt Olenzek
Matt Olenzek

Level 2 Expert

293 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Owen Barnes

Level 3 Expert

867 Answers

Are you a Proform Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...