Question about E-Machines eMachines Desktop PC

1 Answer

T6410 EMACHINE TRYING TO CONNECT START BUTTON

THE BUTTON HAS THREE WIRES ONE IS POWER SW BL\WH COLORED WIRE THE NEXT IS POWER LED GREEN\WH WIRE AND THE LAST IS H.D.D LED RED \WH WIRE ON THE MOTHER BOARD THE ONLY MARKS THERE ARE JFP1 AND JFP2

Posted by on

  • JJFISHER1 May 13, 2009

    THANK YOU THAT DID THE TRICK! YOU HAVE MADE MY DAY ADN GATEWAY WOULDNT HELP THEY TRYED TO SELL ME A NEW UNIT LOL! I WILL HELP IN ANYWAY I CAN FOR THOSE WHOM HAVE QUESTIONS

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,992 Answers

The motherboard in your computer is an MSI MS-7145, which is also called RS480M. You can download a copy of the manual here. The front panel connections are on page 2-20.

Looking at the header JFP1, pins 1 through 9 (odd numbers) are the front row, pins 2 through 10 are the back. Pin 10 is the missing pin. The power switch connects to pins 6 and 8. The power LED connects to pins 2 and 4. The HDD LED connects to pins 1 and 3. The reset button, if used, connects to pins 5 and 7.

Posted on May 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

T6216


There should be 2 rows of pins in parallel usually around the bottom edge of the motherboard. The markings for which is which should be next to them on the board. HDled+, HdLed-, PwrSw, PwrLed, or something similar.

If you do find them but the hard drive Led does'nt come on it's because the plug for it needs to be turned around the opposite way, Led's only work one way as they are diodes. Same for the Power Led.

If there are no letters near the pins then you would have to find the motherboard manual.

Jan 28, 2012 | E-Machines eMachines Desktop PC

1 Answer

Power Button wire to mother board power led power sw HDD Led . what pin connects to the three wires from power button. Led Power wire to what pins, HDD Led to what pins and power SW to what pins on the...


There are may motherboards, but most have writing on them as to what is suppose to plug where. For example, for the power switch, the lettering might be "Pwr" or "Power" or "Pwr sw". The pins are usually together and should fit the plug on the end of the wire.

Nov 25, 2009 | E-Machines eMachines Desktop PC

1 Answer

I unplugged my power sw wire, hdd led, and power led of my emachines t6520 ive tried everything but the computer will not turn on the motherboard does not have any symbols to indicate pos or neg . . . . |...


open up you pc case...mind out for static! dont touch what you dont have to and look for a printed ( normaly white ) motherboard model id..this might be the name of a manufacurer or just a few letters and numbers plus a revision number at the end. armed with these, trot of to google and stab them in. you should see a host of sites, but look for one that is the support site for your board...track down you board on the support/download site and there should be a manual & drivers ect to help you :)

Oct 07, 2009 | E-Machines eMachines Desktop PC

2 Answers

Pinout on t6410 gATEWAY CONNECTING POWER BUTTON


Take a picture of your motherboard and then make printed copy. Call the technical service department and give them the make of your computer and model number, also give them the name of the motherboard and its model number with revisions. Ask them to look up the wiring diagram showing the external connector hook-up from the case to the motherboard. Write down the pin connections on the photo. You can share this information with other people who are having the same problems. Remember to always take a pictures of your set up before disassembling the unit. So you can reassemble the unit correctly. These units are so proprietary that it is almost impossible to find this information without their help. Hope this helps you with your problem.

May 13, 2009 | E-Machines eMachines Desktop PC

1 Answer

TRYING TO HOOK UP MU POWER BUTTON NEED TO KNOW


Hi there
The front panel connectors are mainly,
  • harddisk activity connector
  • power switch connector
  • reset switch connector
  • power LED connector
  • speakers connector
  • USB connector
Harddisk activity connector
This normally comes red in colour and is labeled as HDD-LED
Power switch connector
This comes green in colour and is labeled as POWER-SW
Reset switch connector
This usually comes grey in colour and is labeled as RST-SW
Power LED connector
This is usually green in colour and is labled as PWR-LED
Speakers connector
This speaker will give different beep sounds during boot to tell the user if there is any errors. It occupies 4 pins, however only 2 is important for the function. Be sure to connect the red coloured cable to the positive polarity and the black to the negative.
front_panel_connectors.jpg Front panel connectors pins on the motherboard
front_panel.jpg Front panel connectors from the casing

Good luck and thanks for using FixYa!!

May 13, 2009 | eMachines T6420 PC Desktop

2 Answers

NEED POWER SWITCH WIRING FOR A EMACHINE T-3095


check on the motherboard there should be a small prints on it near control panel.

Mar 05, 2009 | E-Machines eMachines T3830 PC Desktop

2 Answers

Front panel connections


Hi sjcrofts,
The most common problem for most people is knowing what wire color is positive & which wire color is negative. The colors blue, red, green, light blue, light red & light green are normally positive. The color white & black are negative. Your board uses only 2-pin connectors. The 3-pin power connector can be turned into a 2-pin connector to work with the M848ALU pins.
(Page 13, PANEL1). How to? Take the three pin connector, on the back side of the connector you'll see a small tab that holds the wire into the connector. Use a needle & pull tab up while pulling the wire out at the same time. The wire should slide out. Insert the wire back into the connector next to the other wire. You do not need to hook up the SUS led which stands for suspend.

dff74fa.jpg

Pin 1 is positive & the manual shows this by adding the _P = positive.
Pin 3 which is to the right of pin 1, is negative for the hard drive led. Pins 9 & 10 are not used.

Good luck sjcrofts!
Mike

Nov 30, 2008 | PC Chips M848ALU Motherboard

1 Answer

Proper connection


if u look real close to the pins on the board they will say pwd led and power sw ect ect please keep me posted if you need more help identifying these pins

Aug 06, 2008 | E-Machines eMachines Desktop PC

2 Answers

System panel connector


Some vary with respect to wire color. You're case's LED's are no different. You must find the common color for ground. Usually ground is the color white but can also be black. Colors like blue, green & red are normally power +. If I understand what you are saying above is, this case uses three pin connectors. The middle pin is not used. So you need to remove the wires to make it a two pin connector. This will leave on empty pin hole, (not used).
It is not uncommon for you to remove the wire out of the case pin connector & relocate the wire making it a two pin connector. To do this (remove the wire from a case connector & replace it to function as a two pin connector). Find a large needle. On one side of the plastic pin connector you'll see a piece of metal. It locks into the pin connector. Press the needle onto the metal & pull the wire at the same time. Pushing on the metal will depress its locking ability & the wire will slide out easily. (If it does not come out easily than you must be pushing at the wrong end of the metal). Look closely, one end will depress.
Arrange the + & - wire next to each other so it will work on you're board as shown in you're manual.

Good Luck!
Kind of tough explaining this.
Mike

Jun 14, 2008 | ASUS P5S800-VM Motherboard

2 Answers

Wiring info


Most Mobo's have printing next to the places that are jumpered or pluged into. The ones you need sould be close to the edge of the mobo, that is close to the front {power button} side.

May 30, 2008 | E-Machines (308714) Motherboard

Not finding what you are looking for?
E-Machines eMachines Desktop PC Logo

893 people viewed this question

Ask a Question

Usually answered in minutes!

Top E-Machines Computers & Internet Experts

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18387 Answers

Are you an E-Machines Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...