Question about EliteGroup GF8200 MCP78S AM2+ Atx 32GB Pcie 3PCI 2PCIE (GF8200A) Motherboard

1 Answer

Pc monitor blank

I've built a new pc and booted up into the bios and set it to boot from the dvd drive(to install os),then i exit and save changes and the monitor went blank it was as if there was no signal going to the monitor the pc starts up ok the fans spinning ect but nothing on the monitor, after trying everything i could think of graphics card different monitor ect i took the battery out of the motherboard to reset it and this time when i powered up it worked but i get this message "dqs training failed on previous boot, reverted to slower dram speed" so i went into bios set my dvd drive as 1st boot option again then exit and save and i'm back to square one with nothing on the monitor.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 91 Answers

Perform a system restore to see if it will restore your settings.

Posted on May 12, 2009

  • AJ Jones
    AJ Jones May 12, 2009

    Perform a system restore to see if it will restore your settings.

  • AJ Jones
    AJ Jones May 12, 2009

    Perform a system restore to see if it will restore your settings.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

First boot of Win 7. New PC build


Hi.

First of all when you are in the BIOS and have set the DVD/CD drive as the first boot device make sure you save the settings before you restart the computer as it will not remember the changes if you don't.

Make sure that the lens on the CD/DVD drive is clean and also make sure the Windows 7 install disk is clean and free of any finger prints.

make sure that you keep tapping a key when the drive spins up as sometimes people miss the "Press any key to boot from CD/DVD" message.

If you still can't get the disk to boot then try the install disk in a working PC and see if that reads the disk. If it does then the optical drive could be faulty or does not support DVD format.


Regards.

Feb 04, 2013 | Microsoft Windows 7 Home Premium 64BIT...

1 Answer

No booting


Make sure your CD/DVD drive was set-upped as first boot. You can do that changing the BIOS settings. You need to press (one of the following keys depending on the motherboard) either F2, TAB, DEL, F10. then, go to Boot Device Priority, set the CD/DVD as first boot, SAVE your settings, Insert your OS CD, save and Exit.

Sep 06, 2012 | IBM (02R4087) Motherboard

1 Answer

HP dx6120 wont boot from cd rom and I want to install windows in a new haerd drive. Is this a bios problem? How do I deal with it.


Possibly a bios problem if the bios is not set to boot from a cd/dvd.
Press Delete key or F2 as soon as you switch on, or whichever key it needs to get in to the bios. Change the boot option to boot from CD/DVD first. Save settings and exit.

Some computers have a one time boot menu which lets you boot from whichever drive you like just for that time. Usually F11, F12, F2.

Jan 28, 2012 | HP Computers & Internet

1 Answer

Format aspire4736z


Hi there.

To format you will need:
Operating Systems (OS) CD/DVD

Steps:
1) Enter the BIOS when the laptop boots by pressing the Delete key repeatedly.
2) Once the BIOS is open locate the boot disk priority and set prioity 1 to the CD/DVD drive, set priority 2 to the laptop's hard drive.
3) Save changes to the BIOS and exit. The system should now reboot.
4) Insert your OS CD/DVD.
5) Press Enter when the system asks you if you want to boot from the CD/DVD.
6) The OS setup should now start, the first thing it will ask you to do is format your hard drive.
7) After you drive is formatted you can either continue with the setup and install a fresh copy of the OS or you can exit leaving the main drive clean.

~ Slasher_X

Sep 25, 2011 | Computers & Internet

1 Answer

I have a Dell vostro 3700 purchased only a few months ago. The hard drive crashed. After replacing the internal hard drive with new seagate, 750GB 7200rpm, how do I reinstall the OS? I turned off the...


Hi.

Pop the install DVD into the drive and restart your laptop. When you see the Dell logo hit the F2 key to get you into the BIOS. Look for boot options in the list and set the DVD/CD drive as the first boot device. Save the changes and exit the BIOS.

The laptop should restart and boot form the DVD/CD drive so you can install the operating system.



Good luck and regards.

Sep 05, 2011 | Dell Vostro 3700 Laptop Computer PC...

1 Answer

When i start my laptop the system doesnt boot and gets stuck after main memory check page. I need a help on this. When ever i power on system doesnt read os to laod at all and shows blank...


You will need a WinXP CD....
insert the CD and re-boot...
if boot seq is not set to boot from CD change it
restart PC...immediatly press either (F1, F2, Del) key to got to BIOS menu....
look for boot seq,
change the 1st boot dev to CD/DVd rom
save and exit BIOS menu
re-boot....
let the PC boot from CD
follow on screen inst...to reapir the OS or reinstall OS
for more info
got to my site
www.sureshayyar.110mb.com

Reg
Kris

May 08, 2011 | Fujitsu AMILO PC Laptops

3 Answers

Boots only to bios settings, then blank screen after save and exit. will not take a cd boot.


Hello, since it can boot to bios setting, then have you try configuring the boot order,the cd drive should come first,after that your hard disc, if the hard drive comes before the cd rom then it would not recognise it. Change the settings and Save this settings, then try to boot from the cd again, if this does not work then i am rest assured that your hard drive has a problem,and you need to find solution to it by getting a new one. cheers Regards

Dec 01, 2010 | Acer Aspire One Netbook 8.9" Notebook

2 Answers

Concerning a thinkcentre ibm 8183 pentium 3: I put in a blank new hard drive and am wanting to instal a new os from the dvd drive...using f1 to get to different boot options..i choose boot from dvd drive...


your bios settings are not saved because of low voltage of CMOS cell.
Change your cmos cell from motherbord.
CMOs cell gives power to bios flash memory so settings saved.

Aug 15, 2009 | IBM ThinkCentre S50 8183 - P4 3 GHz...

3 Answers

Changing Sony Vaio BIOS


you should be able to exit and save changes, which my guess is you are exiting without saving the changes. theres is a way around this, by pressing either F8, F9, F10, or F12 to access the boot menu, and then you can boot from cd to install your linux operating system

Jan 09, 2008 | Sony VAIO PCV-RX511 PC Desktop

Not finding what you are looking for?
EliteGroup GF8200 MCP78S AM2+ Atx 32GB Pcie 3PCI 2PCIE (GF8200A) Motherboard Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top EliteGroup Computers & Internet Experts

David
David

Level 3 Expert

778 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

Jerry Umali

Level 3 Expert

979 Answers

Are you an EliteGroup Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...