Question about Kenmore 22422 Top Load Washer

1 Answer

My Kenmore Series 80 washer model 23832100 spins slowly

Clothes are too wet for the dryer. I opened the top and defeated the limit switch. If I start moving the tub then it will spin and gain speed but never reaches full speed.
I am looking for the diagrams of this model but no luck from Sears. Hope someone out there can help Thanks.

Posted by on

  • 1 more comment 
  • fixitkevi May 13, 2009

    Ihave a Kenmower washer modle number 11020722991 it goes threw the cycles but it leaves the clothes to wet

  • rick1635 May 14, 2009

    I had the clutch but I can't get to the bolt in the spin tube (agitator) I removed the agitator cap and there is a plastic piece that I can't figure out how to remove. I have a picture of this but don't know how to upload it.

    Thanks for any help

  • rick1635 May 19, 2009

    It was the clutch! Strange even after looking it over it seemed to be fine but once I changed it out the spin mode functioned. Thanks for the help!

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 43 Answers

It probably is your clutch. You will need to remove transmission to repair this.

Posted on May 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore model 11020842990 series 80. had a severely unbalanced load in the rinse cycle. opened lid, rearranged clothes, would not start up again. Removed clothes to dryer, luckily most of water had...


when it went unbalanced the tub most likely broke the lid switch part
3949238.open the lid,on the right side of lid you'll see a strike,it goes into a hole and this is where the lid switch is,stick a screw driver into the hole,if you don't hear a clicking sound the switch is broke
http://www.youtube.com/watch?v=MFsvLiuTniU

Oct 15, 2013 | Kenmore 24032\24036 Top Load Washer

1 Answer

I have a kenmore 80 series and its not spinning out the water.


does it drain out the water and spin but the clothes are still wet or is it not draining or spinning?set the timer to spin,open the lid and stick a screw driver into the lid switch hole and see if it spins and drains,also if it doesn't push down and let the switch up,or close the lid down and open it a little do this a few times,you should hear the switch make a clicking sound,if it doesn't click you have a bad lid switch.if the machine is draining and spinning but the clothes are wet,do the same thing with the lid switch and watch it spin with the lid open,is it spinning fast,if not you have a bad transmission and it's not spinning fast enough to remove the water out of the clothes or you could have a kink in the drain hose or something in the pump and it's not draining all the way.let me know what you find and send the model number off of the washer,the number should start with like 110.

Apr 14, 2011 | Kenmore Washing Machines

1 Answer

Kenmore 80 series model 110 after wash clothes are left soaking


when empty and off, open the lid and see if you can rotate the inner wash basket by hand. if you can easily, then the clutch is worn. This will prevent the basket from going into a high spin and wringing the clothes out. Replace the clutch by removing the top control panel, removing the clips that hold the cabinet, pull cabinet off, remove drain pump clips and pump, remove motor clips and motor, remove transmission (3 bolts). Now you will have access to the clutch, replace as needed, reverse dissasembly to complete. remember to unplug.

Jul 01, 2009 | Kenmore 22422 Top Load Washer

1 Answer

Wet clothes


the reason the clothes are wet is the washer is not shifting to high spin,does the washer have a speed switch(normal wash spin,high wash spin)if its not the speed switch than the clutch is bad,how old is the washer?mike

Apr 19, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Washer won't spin


pull the fab soft dispenser out and pry off the cap that sits on top of agitator looking down inside there you'll see 4 pieces called agitator directional cogs(dog ears) they are worn and need replaced

Apr 06, 2009 | Kenmore 22422 Top Load Washer

3 Answers

Kenmore washer 80 series 110 model not spinning.


unless your washer is over 20 years old, then it wont have a belt. the temperature of the water wont have anything to do with it spinning or not.
need to know if it agitates or drains and just wont spin.
if it agitates but no spin or drain, then you have a bad lid switch.
if it wont agitate or spin, but will drain, then you have a broken drive coupling.

Jan 08, 2009 | Kenmore 24032\24036 Top Load Washer

Not finding what you are looking for?
Kenmore 22422 Top Load Washer Logo

689 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Sal DeAngelo

Level 3 Expert

2290 Answers

fordexpert

Level 3 Expert

5537 Answers

Ed Mac

Level 3 Expert

731 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...