Soyo mbw-serial too dim - Samsung SyncMaster 214T Monitor

Table 1: 4-Wire Ignition Switch Table
The body control system consists of the following 3 modules:
• The dash integration module (DIM)
• The instrument panel integration module (IPM)
• The rear integration module (RIM)
Each of the 3 body control modules integrate a number of functional systems under the control of a single module. Each of the modules are connected to the Class 2 serial data line; many control signals are implemented by Class 2 messages.
Dash Integration Module (DIM)
The DIM is wired to the class 2 serial data line. The various DIM input and output circuits are described in the corresponding functional areas as indicated on the DIM electrical schematics.
The DIM functions include the following:
• Control of headlights and exterior lamps
• Horn relay control
• Interior lamps incandescent dimming
• Lamps On signal with wiper/washer
• Power moding control over Class 2 serial data line
• Steering wheel controls
• Storage of the clock settings and, sending a message out on the class 2 serial data circuit in response to requests from other modules

fixya doesnt have access to your or other company accounts need to notify MBW ASO Wireless and inquire about the account in your name and same with your bank

Check for resistor and diode errors

The monitor is going bad. The capacitors that drive the screen are getting weak. It is too expensive to fix, you'll need a new monitor.

Hello,
The exact specs for compatible RAM for this motherboard is: SDRAM, PC133 • CL=3 • Unbuffered • Non-parity • 133MHz • 3.3V • 32Meg x 64
You might find this RAM on Ebay, or Tigerdirect.com, memoryexpress.com, etc... though it is old so it might be hard to come by.
http://www.crucial.com/store/listparts.aspx?model=SY-5EHM&Cat=RAM
Regards, Chris

call the manufacterer.

Just enable the SATA and your system should look up any installed SATA disks and boot from there. Just give it a try first.

Are you using it with or without Mionet?

If you have the MBW blue rings version it may be a compatibility issue.

NB: only do this if you're not using mionet! (this is for MBW Blue Rings)

If the drive worked without problems for a period of, perhaps you could try resetting it (this will reset the drive to DHCP - If you had it set to static before and the login details will be default again username: admin | password: 123456). Your data will not be effected by the reset

Reset for MBW White Light: (refer to the link for reset prosses using mionet in the last link)

http://wdc.custhelp.com/cgi-bin/wdc.cfg/php/enduser/std_adp.php?p_faqid=3553&p_created=1241119153&p_sid=lnbHW1Tj&p_accessibility=0&p_redirect=&p_srch=1&p_lva=&p_sp=cF9zcmNoPTEmcF9zb3J0X2J5PSZwX2dyaWRzb3J0PSZwX3Jvd19jbnQ9NjgsNjgmcF9wcm9kcz0yMjgsMjA5LDI2MyZwX2NhdHM9MCZwX3B2PTMuMjYzJnBfY3Y9JnBfc2VhcmNoX3R5cGU9YW5zd2Vycy5zZWFyY2hfZm5sJnBfcGFnZT0xJnBfc2VhcmNoX3RleHQ9cmVzZXQgbXkgYm9vayB3b3JsZCB3aGl0ZSBsaWdodA!!&p_li=&p_topview=1


If you are using Mionet, refer to this link for instructions:
http://wdc.custhelp.com/cgi-bin/wdc.cfg/php/enduser/std_adp.php?p_faqid=3262&p_created=1231875761&p_sid=lnbHW1Tj&p_accessibility=0&p_redirect=&p_srch=1&p_lva=&p_sp=cF9zcmNoPTEmcF9zb3J0X2J5PSZwX2dyaWRzb3J0PSZwX3Jvd19jbnQ9MTAsMTAmcF9wcm9kcz0yMjgsMjA5LDIyMSZwX2NhdHM9JnBfcHY9My4yMjEmcF9jdj0mcF9wYWdlPTEmcF9zZWFyY2hfdGV4dD1yZXNldA!!&p_li=&p_topview=1

Hope this helps!

I'm curious as to why you need a serial number to get viruses out of it. No program that scans for viruses that I know of asks for a serial number.

Go to a recognized site such as mcafee.com or trendmicro.com and look for the free virus scanning utility.

sounds like the power module went bad- the part is most likely cheap- but getting to it is NOT. Take it to a repair shop for an estimate- you might be better off buying a new one though...