Question about Jet Tech Systems 24 in. F18DP Free-standing Dishwasher

1 Answer

JET TECH/model F18/small amount of water stays in bottom.Wont fill or cycle but water runs.

Posted by on

  • Anonymous Mar 20, 2014

    repleacing water pump

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 5 Answers

Hello,

It is normal to have 4 or 5 inches of water inside the dishwasher unless you remove the stand-pipe (located inside, front right side). This pipe should be removed at least once a day and the dishwasher should be drained. Don't forget to turn the power off first.

For more info goto to

http://www.mvpgroupcorp.com/jettech/support.htm



Robert

Posted on Jun 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jet tech f18 dp will not stop running. timer water level ?


one has to think timer or the control board failure

Nov 22, 2016 | Washing Machines

1 Answer

Jet tec f18 water goes to 120f redy light does not come on will not wash got hot water to 120f open door have steem but no wash frank


Verify the contactor for working condition. maybe burned wires or bad contactor. if it is good then the rinse thermostat or, less likely, the booster element.

Oct 07, 2013 | Jet Tech Systems 24 in. F18DP...

1 Answer

Washer fills wont wash or spin out water makes noise and a very small amount of water flow's from the holes on the front left of the tub


Hi.

You need to run a diagnostic cycle. The procedure is illustrated in a paper tucked inside the control panel. To get the guide to diagnostic remove the top console panel. You will need to disconnect power and undo three screws.

If the paper is not there, try giving me the full model number, I see if I can get service manual for this model.

Sep 18, 2010 | Kenmore 24032\24036 Top Load Washer

1 Answer

WATER FILLS WONT SHUT OFF


The pressure swith (load size) is what controls that chang that. A small hose runs from the bottom of your tub and as the water fills a measerd amount of water fills that tube and pressure build up in their operates that switch and activates the timer to stop filling and start agitating.

Jun 06, 2010 | Kenmore 24032\24036 Top Load Washer

2 Answers

Water runs but doesn't fill tub and wont spin if put on spin cycl


The water-level switch regulates your washer's fill volume. This switch is usually a diaphragm device with a small, clear tube attached between the switch and the bottom of the washer's outer tub. As the water level in the tub increases, the pressure on the air in the tube increases. When the pressure reaches a certain level, it activates the switch, shuts off the water, and signals the timer to begin the agitate cycle. If the switch is defective, it may prematurely signal the water to shut off. If so, you probably need to replace the water-level switch.

Jan 09, 2010 | GE WBSE2090A Top Load Washer

1 Answer

Machine starts to fill then stops and beeps


try it on rinse cycle if goes ok then the hot water valve is faulty

Dec 14, 2009 | Fisher and Paykel Fisher & Paykel Washer

2 Answers

Dishwasher keeps pumping out - won't start cycle - green light flashing on panel


I had same symptoms on a Hotpoint dishwasher.
Turned out to be a failed water heater.
The logic in this case goes like this:
When wash cycle starts, the first thing the machine does is pump out any water that has collected in the sump since it was last run.
It then allows a small amount of clean water in and enables the water heater.
If heater okay, it then continues with the rest of cycle.
In this case, the control board detected failed heater so pumps out the water and then stops with an error code shown by a flashing lamp.

No simple fix I'm afraid - machine had to be turned on its side, bottom panel removed, several items had to be removed to get at the water heater which was then repalced with a new one.

You dont state what make/model your dishwasher is so maybe worth adding this information as someone else may recognise your fault and have a quick fix.

Oct 02, 2009 | Dishwashers

2 Answers

My dishwasher Bosh Model SHU43C06UC has the drain clog


first feel around the drain and see if there is something stuck inside the drain. then take a small amount of clorox2 powder and run it through a cycle. after that try jet dry. sometimes there is a grease build up or a lime build up that needs to be removed.

Apr 23, 2009 | Bosch 24 in. SHU43 Built-in Dishwasher

1 Answer

Descale red light, wont go off, and can i use any delcale tabs


Solution: Just refill the water tank with water (no descaling solution) all the way to the "Max Line". Then run the full descaling program again --takes approx. 20 minutes. After the program runs completely you will get the yellow "standby" light on and the red "descaling" light will be off.

Next time you descale, be sure and fill your water tank to the "Max Line" before running the descaling program.
Hint: An incomplete cycle (not full tank) is what makes the red light stay on. In other words, it's staying red to tell you to run a full cycle (beginning with the water tank filled to the "Max Line"). Hope this tip is helpful!

Mar 12, 2009 | Bosch Coffee Makers & Espresso Machines

8 Answers

Why is the fault F18 error code on my bosch washing machine flashing?


Open the small flap at the front bottom right of the machine. DONT unscrew the circular white knob yet!!! Use the small black hose to drain the machine into a tray, by removing the small cap on the end of the hose. You will have to use a tray, rather than a bowl because the hose is only short, and keep emptying the tray.(put a washing up bowl next to the machine, so you don't have to carry the tray.) If water does not come out of the hose, then gently unblock it with a piece of wire or fine knitting needle. When water finally stops coming out of the hose, it is time to gently unscrew the white knob anti-clockwise, and pull it forwards. Now you can clear the debris out of the pump rotor, which is behind the white knob. Check with your finger that it can rotate freely, then replace the white knob firmly. Make sure the small cap is replaced on the end of the hose, clip it back into place and put back the cover panel. If this doesn't work then there is a blockage deeper in the machine, and dismantling will be required. Good Luck!!

Feb 03, 2008 | Bosch Logixx WFT 2806 Front Load...

Not finding what you are looking for?
Jet Tech Systems 24 in. F18DP Free-standing Dishwasher Logo

Related Topics:

477 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jet Tech Systems Dishwashers Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Brad Brown

Level 3 Expert

15557 Answers

ray gallant

Level 3 Expert

43020 Answers

Are you a Jet Tech Systems Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...