Question about Irons

1 Answer

Good Morning. I have a B&D ProFinish Premium Iron which I purchased in 1998 - I've been very satisfied with its performance and only the cord has been replaced. Today, however, despite the gauge being set at 4 and up, no heat is possible. What do you think I should do?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

You must chek if the power is present inside iron if is ok yu need to change thermostat or heater.

Posted on May 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Half my flat iron will not heat up


i'm lookin gfor a solution too; mine was fine one day, now both plates wont heat, even though it says its gotten to the temperature i set. Someone else said the heating coils might've burned out and to get a new one?

Jun 26, 2012 | Remington Pearl Ceramic Ultimate Flat Iron...

1 Answer

My Pro Finish 714 cord was accidentally cut. Is it worth replacing the cord? Where do you get a new cord and can I replace it myself?


Thank you for using FixYa. Is the cord cut near the iron end or the outlet end? could the cord be shortened? A new cord can be purchased at most reasonable hardware stores and with a little care and attention can be replaced yourself.

Hope this has been of some help.

Mar 04, 2011 | Black & Decker ProFinish X750 Iron

2 Answers

The electrical cord is very hot at the point where the cord enters the iron


mcdevito75 here, You may have a problem with the heating element in your iron, Check to see if you have a Warrantee if so, return the iron to Black & Decker. In the meantime look for an appliance repair shop in your area and have the iron checked out.

Aug 07, 2010 | Black & Decker Prestige Plus Premium X830...

1 Answer

Black rubber burned onto plate of iron


Hi,
Here is a tip that will help you with that problem...

Cleaning a Steam Iron Soleplate
http://www.fixya.com/support/r5301167-cleaning_steam_iron_soleplate

heatman101

Apr 12, 2010 | Black & Decker ProFinish X750 Iron

1 Answer

Iron requires new cord


I don't know what brand of iron you have, but most irons are not repairable. I work for Black & Decker and if you needed a new cord for one of our irons, you'd have to replace the iron.

Unless you paid a small fortune for your iron ($100+) and you can see where the cord on your iron is able to be pulled out without taking the iron apart, chances are you'll have to purchase a new iron.

I hope I've provided you useful assistance and that this information allows you to make an informed decision as to how to proceed from here. Please be sure to vote on my response. I hope I've earned a good rating from you today.

Please post a comment if you need additional assistance so that I can help you further.

Jul 14, 2009 | Irons

2 Answers

How to clean the plate of a black and decker iron that has build up?


you can take the solution for descaling coffee machines and set the iron in a layer of less the 1/4 inch deep.
you can clean out the holes with a needle. than run the selfcleaning cycle.
leave the sole in for about 15 minutes. Than clean with non scratching scotch brite.

Apr 28, 2008 | Black & Decker ProFinish X750 Iron

Not finding what you are looking for?
Irons Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Irons Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18394 Answers

kakima

Level 3 Expert

102366 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Are you an Iron Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...