Question about Car Audio & Video

1 Answer

Need the demension " hole" to be cut out of the box, so the kickers can fit." I will audio box for two 15" kickers to fit. I will have home depot cut the wood and size the hole.

Need to build a audio box. i have 15" solo baric kicker subwoofer " need to know dimension of the hole to be cut out.

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

The cutout simensions for the kicker 15" solo baric are 13.75".

Posted on May 15, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I bought replacement blades for my John Deere 54 inch cut and they came with a round center hole and the ones already on there have a jagged center. Is there a piece to fit inside round hole to make blade...

Those piece you are looking or should have come with the replacement blades , if not you might be able to find them at you local home center ie: lowes ,home depot..

Apr 02, 2011 | Garden

1 Answer

I have 2 15 in 02 L7s an 2 2000w mono blocks the box they came in is to big for my trunk so i had it custumized to fit so its a lot smaller now its 16in high 21 inchs deep an 40 inches long and is angled...

When porting a box, you have to have the air resistance just right. If you are just gunna cut a random hole, id say you are better off keeping it sealed. And proven fact, bass comes out the back of the speaker so face it away from ya and toward the back of the car. Then you wont hear any Speaker Slap either

Feb 03, 2011 | Kicker Solo-Baric L7 S15L72 Car Subwoofer

1 Answer

Need the measurements for a sealed box for a kicker s12d subwoofer

If it's it can even get home depot or rona to pre cut the 3/4 mdf for you. You need a box that's 1 cube interior volume which is 12x12x12 or 13.5 x 13.5 x 13.5 outside, so you need 6 pieces of mdf, two (13.5x13.5), two (13.5x12), and two (12x12). Don't worry about driver displacement as it's about .08 cubes, so you'll still be at .92 cubes after that, and it will simplify your design. Get some glue, screws, and caulking (or use the glue like i do). Put it together, let it dry, seal it, and then paint, cover, or leave it as is. Cut your 11" hole for your speaker, drill a small hole for your speaker wire (forget terminal caps), run your wire and then seal the hole with caulking, mount your speaker using a gasket or rope caulk, hook it up and enjoy.

Oct 07, 2010 | Kicker S12D Car Subwoofer

1 Answer

Kicker 8 inch l5 problem!

Possibly. Actually there are sub rings you can buy to convert a regular box over to one that will accept a square sub without cutting the whole out in your box to make it square. The airspace may be lacking a little bit.

May 20, 2010 | Kicker Solo-Baric L7 S15L72 Car Subwoofer

1 Answer

No power to my kicker ZX 1000.1

sounds like you blew a fuse for the battery power supply to the amplifier

Mar 23, 2010 | Kicker ZX10001 Car Audio Amplifier

1 Answer

Broken wire from a nail. how do i fix/splice?

I think you are saying a nail was driven into your wall and has gone through your thermostat wires? If that's the case here is a simple solution. Go to your local building supply such as Home Depot. Buy a an "old work" box which is designed to go into your wall where there is no stud. It will require you to cut a rectangular hole just large enough for the box, then tighten the screws to install... but dont do that yet. Get the box and a white or beige plain cover to fit it. The plain cover should have no holes except for the two screws to afix it onto the old work box. Cut a small hole next to where the nail went into the wires. Remove the nail and pull the wires out slightly. See which side has more slack. Locate the old work box on the side where the wires are shorter or tighter (less slack) and pull the other wire into the box so that both can be spliced together. If necessary finish cutting the wires the nail didn't sever. Do not cut red with any other wire at the same time because red is the power (24 vac hot) going to the thermostat. When you have pulled both wires into the old work box and tied a knot to prevent them slipping out, then fit the box into the wall hole and tighten the screws to draw the box snug to the wall surface. Splice each color with a wire nut, tiny wire nuts that are blue or grey are for 18-24 gauge bell and thermostat wires. Join red to red, white to white, yellow to yellow, blue to blue, orange to orange, green to green, etc until all are finished. Doing this will eliminate the need to research which wires are actually in use for your application. Install the cover plate. Test your repair.

Dec 23, 2009 | Goodman GMS90703BXA Heater

2 Answers

Cutting resin tile

You need a tile saw that uses water to prevent sparking. Home Depot, Lowes..........<$100

Apr 24, 2009 | Daltile Bathroom Accessories Resin Soap...

3 Answers

Hole in copper water supply pipe

solution#2 is one way to do it however those clamps will leak after awhile. You can cut pipe on center of hole and (A) push pipe up and install a copper coupling which does involve soldiering. Or (B) you can get a brass coupling fitting called (Shark Bite Fittings) which simply slides over pipe and locks and seals on pipes. This is a fairly new product and godsend to plumbers and plumbing repair. Whenever fixing pipes in walls check for any form of leaks thoroughly before covering up wall.

Apr 14, 2009 | Plumbing

1 Answer

Kickers dont beat like they should

try to check and clean the wiring as clean as possible to avoid messing up on your connection. Check the polarity of you subs to yuor amp if you have it connected on the outher way around it would not give you a good result. check the polarity this will solve your problem. Over powering your sub will fry it easily try to tune it a 10" sub wont give you a 15" performance..

Jan 20, 2009 | Jl Audio 500/1 Car Audio Amplifier

1 Answer

Kicker kx1200

I am having the same issue, my kicker kx 1200 watt amp was pushing two JL Audio W6 12's and amp has power but no speaker out put, sending my amp to kicker for the thrid time. I tryed in my friends car with no luck.

Nov 20, 2006 | Kicker KX Series 04KX1200.1 1200w RMS...

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

250 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4861 Answers


Level 3 Expert

76132 Answers

The Knight
The Knight

Level 3 Expert

74243 Answers

Are you a Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides