Question about Brother MFC-260C All-In-One InkJet Printer

1 Answer

How do I refill my ink cartridges?

I have bought ink for my Brother MFC-260C ink cartridges but i have no idea how to put the ink in. How do i do it?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 152 Answers

If you bought an ink refill kit, then there should be a bellows with a fine needle tip filled with ink and a rubber stopper. There should have been instructions included with the kit.
If you only bought the bellows and there's no instructions or rubber stopper, then I'm afraid you are missing some pieces. You need more than just the ink to refill the cartridges correctly, or else they will leak all over the inside of the printer.

Posted on May 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My printer is not HP it is Brother MFC-260C


The printer uses several ways to show ink levels. When you replace the cartridge it askes if it has been replaced, Say yes and it sets the ink level monitor to full. As the cartridge empties it them checks through an electronic eye system through the cartridge. When it cannot see any ink it says it is empty.
Replace the cartridges and it should fix the problem.

Feb 22, 2016 | Brother MFC-260C All-In-One InkJet Printer

1 Answer

My Brother MFC 440CN will not recognize a Brother


The usual obvious fix is to buy a new catridge, insert, power off machine, then switch back on to reset any sensors. But if the circuitry on the machine itself is faulty it wont fix it.

I used to own an MFC 260C. It had a perfectly good full ink catridge in it, that was working fine, until...it suddenly did not recognise the cartridge anymore.

I pulled the machine apart and found that 2 of the 4 sensors on the cct board at the back of the cartridge housing were loose. These sensors pass light through the exposed part of the cartridge to see if ink is there. So if these are faulty, you will never clear the "No Cartridge" or "Ink Empty..." or "Near Empty Ink ..." messages on the MFC260C and prbably other similar printers in the MFC range.

Why did they fail? Because the soldering on these sensors was poor quality.

I would never buy another Brother machine because of this, also because they design the machine to be totally useless unless all the ink ccartridges are full. Shame on you Brother, and kiss my *** for the $160 pile of junk I bought off you that was only on its second batch of cartridges (ie very little use)

Jan 23, 2010 | Brother Office Equipment & Supplies

1 Answer

Mfc 440cn printer says 'ink empty' to new full ink cartridge


The usual obvious fix is to buy a new catridge, insert, power off machine, then switch back on to reset any sensors. But if the circuitry on the machine itself is faulty it wont fix it.

I used to own an MFC 260C. It had a perfectly good full ink catridge in it, that was working fine, until...it suddenly did not recognise the cartridge anymore.

I pulled the machine apart and found that 2 of the 4 sensors on the cct board at the back of the cartridge housing were loose. These sensors pass light through the exposed part of the cartridge to see if ink is there. So if these are faulty, you will never clear the "No Cartridge" or "Ink Empty..." or "Near Empty Ink ..." messages on the MFC260C and prbably other similar printers in the MFC range.

Why did they fail? Because the soldering on these sensors was poor quality.

I would never buy another Brother machine because of this, also because they design the machine to be totally useless unless all the ink ccartridges are full. Shame on you Brother, and kiss my *** for the $160 pile of junk I bought off you that was only on its second batch of cartridges (ie very little use)

Jan 19, 2010 | Brother Office Equipment & Supplies

1 Answer

Put new black cartridge in now no black ink what could be the problem


it could be you waited too long to replace the ink and the nozzles are dry, or the ink cartridge you put in is also low or no ink. try doing a couple ink cleanings and do a test print, see if it helps.

Nov 23, 2009 | Brother MFC-260C All-In-One InkJet Printer

2 Answers

Have a mfc-210c brother ink empty cyan replace ink. have put in a new lc41y ink cartridge . machine says open cover and reinstall ink cartridge. sortof done this 20 times!look forward to some advice...


The usual obvious fix is to buy a new catridge, insert, power off machine, then switch back on to reset any sensors. But if the circuitry on the machine itself is faulty it wont fix it.

I used to own an MFC 260C. It had a perfectly good full ink catridge in it, that was working fine, until...it suddenly did not recognise the cartridge anymore.

I pulled the machine apart and found that 2 of the 4 sensors on the cct board at the back of the cartridge housing were loose. These sensors pass light through the exposed part of the cartridge to see if ink is there. So if these are faulty, you will never clear the "No Cartridge" or "Ink Empty..." or "Near Empty Ink ..." messages on the MFC260C and prbably other similar printers in the MFC range.

Why did they fail? Because the soldering on these sensors was poor quality.

I would never buy another Brother machine because of this, also because they design the machine to be totally useless unless all the ink ccartridges are full. Shame on you Brother, and kiss my *** for the $160 pile of junk I bought off you that was only on its second batch of cartridges (ie very little use)

May 03, 2008 | Office Equipment & Supplies

4 Answers

Brother MFC 5840CNZ displays Ink Empty on CYAN when new cartridge is installed


Something that has worked for some Brother owners to get cartridges recognised.

1. With your MFC powered up, open it up and remove the cartridge you are having a problem with, then close the MFC, leaving it powered up. It should report that there is no cartridge in the machine.

Still with the MFC powered up, open it up and reinsert the ink cartridge, then close the MFC. It should either ask if you have replaced a cartridge or go into its cleaning mode.

Answer "yes" to "have you replaced cartridge?" and it should either "print" or "clean" and then "print".



Nov 08, 2007 | Brother MFC-5840CN All-In-One InkJet...

4 Answers

MFC 640CW not refilling with new ink cart.


Unplug printer from power. Wait a minute. Take all carts out. Plug machine to power. mfc demands carts. Reinsert carts (have a look if they all filled with ink!!). If asked press 2 (No change) despite you use a new cart press 1 Yes cart changed.

Should work!

Nov 03, 2007 | Brother MFC-640CW All-In-One InkJet...

Not finding what you are looking for?
Brother MFC-260C All-In-One InkJet Printer Logo

258 people viewed this question

Ask a Question

Usually answered in minutes!

Top Brother Office Equipment & Supplies Experts

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

Ron Dufek
Ron Dufek

Level 3 Expert

398 Answers

James Cagle
James Cagle

Level 2 Expert

453 Answers

Are you a Brother Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...