Question about Pioneer PRO-510HD 53" Rear Projection Television
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Pioneer PRO-510HD Elite
since your tv is 6yrs old it could be that the video circuit has cold solder that needs to be resolder if that does not work then a focus on the video circuit by replacing the component there, it could be an ic or transistors or diode.if you are not a tech get one to look at your set.good luck.for further help email me at email@example.com
Posted on Apr 06, 2007
SOURCE: "TV Not Turning On"
i have the same tv, all i did was take out the power supply board and reflowed the solder on there. i have heard that this is a common problem with these televisions, but its not too hard to fix (just takes about 2 hours to resolder them all). hope this helps
Posted on Oct 26, 2008
the problem with pioneer projection tvs is that when they made the boards they never used enough solder for the circuits and you get cracks in the runs. thats why heat and cold will effect it. I had the same problem and I took out the board and resoldered every track I could and it works good now but my remote wont work if anyone has any info or prints to this tv please post on here
Posted on Sep 15, 2010
SOURCE: Pioneer PRO 510HD - 53"
Boards can run 250 - 400.00 on average. You may be better off just repairing the board parts for around 65.00
Projection TV sets have two very common problems. One is convergence ( 3D/Warped video) the other is CRT fluid ( Dull Video). Here are more details and solutions for both. Repair kits with instructions are also avail from www.TvRepairKits.com
Common Problem #1) Convergence has gone out
Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.
This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.
Common Symptoms include....
For more more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull
Common Problem #2) CRT Fluid is Cloudy
Projection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images.
Picture of a set that needs the fluid changed.
TV set after fluid change
You can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull
Posted on Jan 29, 2011
Tips for a great answer:
Oct 06, 2011 | Pioneer PRO-510HD 53" Rear Projection...
May 23, 2011 | Pioneer PRO-510HD 53" Rear Projection...
Apr 12, 2010 | Pioneer PRO-510HD 53" Rear Projection...
Sep 11, 2008 | Pioneer PRO-510HD 53" Rear Projection...
Oct 12, 2007 | Pioneer PRO-510HD 53" Rear Projection...
Apr 06, 2007 | Pioneer PRO-510HD 53" Rear Projection...
Feb 09, 2013 | Pioneer PRO-510HD 53" Rear Projection...
Jun 23, 2017 | Pioneer PRO-510HD 53" Rear Projection...
120 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: