Question about Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

1 Answer

Hoover Windtunnel We bought a new power cord because our's broke. We cannot figure out how to uninstall the old one and reinstall. My husband has removed just about all of the screws.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,673 Answers

If it goes in just at the bottom of the handle, take off the handle, then remove the tool holder, then you can replace the cord. If it goes in near the bottom, then you will have to remove the motor cover and light to get to the connecting wires.

Posted on Jan 07, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace power cord on Hoover windtunnel vacumm


There are many different models of Hoover Windtunnel so I can't be specific to your model, you will need to determine where the cord enters the unit and how to gain access to the internal wiring. Disconnect the old cord and attach the new cord using the proper connectors.

Apr 02, 2017 | Hoover Vacuums

1 Answer

The bottom cord wrap piece broke off. How do I remove it? I have the new part.


There are little prongs on the end of the cord wrap that expand when pushed into the hole in the vacuum. I've used a small screwdriver to push on the tabs to get the old part out.

Dec 21, 2015 | Hoover U5750-900 WindTunnel Bagless...

1 Answer

How do I replace a severed power cord on hoover windtunnel upright bagless model U5280900?


Hi there! We recommend taking your vacuum to a Hoover authorized service center to have your cord repaired. Follow the link to locate the nearest service center to you. Thanks! Service Center Locator

Oct 13, 2014 | Hoover Windtunnel Supreme U5280-900...

1 Answer

Cord hook broken


You may call Hoover Service @ 440-996-2000

Sep 30, 2009 | Hoover U6616-900 WindTunnel Bagless...

1 Answer

Hello! Hoover WindTunnel broken! aRGGHHH


I would definitely check out the epoxy route.

Jun 14, 2017 | Hoover U6630-900 WindTunnel Bagless...

1 Answer

Need to replace power cord on Hoover windtunnel need wiring help


without seeing this it would be difficult to describe. I would take it to a vac shop and let him show you. there are no real schematics for the wiring of these units. I usually would cut off the cable with a few inches of insulation to know where to install the new one and reuse the old terminals if needed.

I’m happy to assist further over the phone at https://www.6ya.com/expert/robert_b96ba3f038cf317c

Feb 24, 2009 | Hoover U5399-900 WindTunnel Lite Upright...

1 Answer

Replacing power cord


I replace one on my U6439-900. I took the back cover off and had to cut the wires and put new wire nuts on. Then I secured them really well with electricians tape. Might help to even put on a zip tie around the wiring. Hope that helps.

Jul 18, 2008 | Hoover U6437-900 / U6439-900 Windtunnel...

2 Answers

Hoover S3630 WindTunnel


Broken wire reconnected and power was restored.

Jul 13, 2008 | Hoover S3630 WindTunnel Bagged Canister...

2 Answers

Replacing a fraayed and twisted power cord on a Hoover windtunnel upright


ok so I took this vaccum apart completely except for the electrical and motor systems. It seems to me that without dismantling both of these systems on the vaccum you can't replace the power cord. And I wouldn't recommend taking them apart unless you know what you are doing since replacing the power cord seems to require cutting the old power cord and soldering the new one onto the old terminals. All in all its probably easier to get a new vaccum altogether.

Dec 13, 2007 | Hoover U6616-900 WindTunnel Bagless...

Not finding what you are looking for?
Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18424 Answers

Jim Parker
Jim Parker

Level 3 Expert

1041 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

Are you a Hoover Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...