Question about Kenmore Elite 21082

1 Answer

Washer stuck in cycles

Kenmore elite top loading washer keeps getting stuck in all cycles

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

If you suspect you have a defective timer it can easily be replaced by performing the following steps:


1. Unplug washing machine... and pull out the timer knob. Some knobs have a removeable center cap and hidden screw. Some are simply slip-fit. Remove the knob.

2. Remove console. This can be accomplished in one of two ways depending on which type of console you have.

a. If the console has removable end caps, the caps lift off by prying on the top from the back of the washer.
The cap will pull off towards you as you are facing the unit from the front of the washer.
There will be a screw under each end cap that you will need to remove.


b. If the console does not have removable end caps, you will need to slide a putty knife under the front corner of each side and push in while lifting up.
There is a retaining clip under each side that has to be released.


3. Once the console has been released it will lift up and fold back over the back of the washer in its resting position. Use care not to stress the small plastic hinges that hold it on. They can break easily.

4. Disconnect all power plugs and remove the timer's mounting screws.

5. Reinstall reverse of removal.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Posted on Sep 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Kenmore Elite total care system gets stuck on the Pause Cool Down step and then again on the spin setting. It doesn't even drain after rinsing.


The washer has a temp sensor for the rinse cycle , so just set the temp to warm water and it will stop getting stuck, because it wants the water to be warm when it rinsing ,ok hope that helps you! Ericc

Jul 03, 2010 | Kenmore 24032\24036 Top Load Washer

1 Answer

Have Kenmore Elite Catalyst Washer showing F3.


I have a top load Kenmore Gold Catalyst Cleaning Action washer that is stuck on permanent press mode. The digital display reads 8 min. and will not turn off or clear.When it is turned on the, the timer goes to 37 minutes and beeps repeatedly through all cycles. It will not clear even when I unplug it. How do I fix this annoying thing!!? Thoughts please.

Bill

May 22, 2010 | Kenmore Washing Machines

1 Answer

Kenmore Elite Top Load..Rinse water keeps running in Spin Cycle. Clothes are soaking wet when spin cylce is complete


the fill valve is an electric magnet valve and sounds like it is stuck unplug machine disconnect water lines plug in and when u turn on does it click, if yes then unplug try to slide a long qtip in and if it goes in replace valve

Jul 06, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

Kenmore elite washer leaks water in spin cycle


You need to replace your pump. Make sure you have the washer either on something that will absorb water, or fix it outside/garage. Because these pumps hold extra water and that is why it is not recommended to keep them outside to do laundry in colder climates. The water can freeze in the pump and wreck it. Good luck. They actually are pretty easy to replace.

Apr 26, 2009 | Kenmore Washing Machines

1 Answer

*&^% screws!!!


F2 = Long Drain. Most common cause is something (or lots of things) stuck in the drain pump. There are screws at the bottom of the front panel that can be removed to check it out. If the screws look like stars they are Torx head screws, get driver from most home centers.

Go here for Kenmore HE3 washer parts:
http://www.repairclinic.com/Kenmore-Washing-Machine-Parts

www.RepairClinic.com

Feb 03, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

I have a Kenmore Elite Washer that does not complete the wash


The timer should be checked/replaced.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Jan 12, 2009 | Kenmore 22422 Top Load Washer

1 Answer

Clothes stuck under agitator pan


You'll need to remove the agitator.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Jan 08, 2009 | Washing Machines

1 Answer

Kenmore elite top load washer


error code with this? f11 or f22 are control board related commucation errors.

Jun 02, 2008 | Kenmore Elite 45986 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Sal DeAngelo

Level 3 Expert

2510 Answers

fordexpert

Level 3 Expert

5575 Answers

Ed Mac

Level 3 Expert

731 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...