Question about KitchenAid KSM75WH WhiteTilt-head Stand Mixer

1 Answer

Ksm75wh mixer stopped running

Stopped running

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • KitchenAid Master
  • 1,225 Answers

Check carbon brushes under the black caps on the motor sides. They only go in ONE way so take care, there is a blocker in the square hole on one corner. Line it up with the missing brush corner. If it's not the brushes remove the back cover & check for broken wires. Do your checking with power unplugged.

Posted on Dec 01, 2013

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 87 Answers

SOURCE: Stopped running

there is a thermal fuse inside tapped in-line of AC cord .if it was under a heated load it will blow non resettable . need a test meter to check for continuity .electrical flow . with machine not plug in , these items are very small .187 diameter and are crimped in line of AC cord , these are going to cost about $8-10 dls us can be bought @ Radio Shack rating should be about 8-10 amperage , good luck >^.^<

Posted on Mar 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Kitchenaid mixer will not run on speeds LOW SPEEDS only runs on speed ten. I&#39;ve replaced the phase board and that was not the issue. what else could be causing this problem


If it does not start at all until you get to speed 10 then look for a broken wire an any of the wires NOT associated with the phase board. Highly unlikely since you have just been there. Next look at the operation of the switch low down inside the black speed control board. There is a primitive switch there operated by a shaft from your speed control lever. You may find the switch is not activating until it gets right up to speed 10. Have you checked the carbon brushes? The phase board you have just done is normally the culprit for your problem.

Dec 20, 2014 | KitchenAid KSM75WH WhiteTilt-head Stand...

1 Answer

The mixer would not come up to the speed when speed lever is moved from off position to any other speed provided. The mixer would start spinning and then stops immediately. Any suggestions?


You either need to adjust the speed control switch under the rear dome or you need to replace the switch, I think you can find on YouTube videos on how to adjust speed control switch and the part is easily available on the internet. AND!! you can do this repair without a full tear down.

Sep 18, 2013 | KitchenAid KSM75WH WhiteTilt-head Stand...

1 Answer

My preeti lavender stopped workng suddenly


If its new, I would return it for warranty.

Dec 31, 2012 | KitchenAid ProLine 600 Stand Mixer

1 Answer

I have a KitchenAid mixer Model K5SS, Ser #W83808959. The motor stopped running and in checking the brushes, I found they are are both stuck in the brush holders. I suspect this is the reason the motor...


Download a Copy of the Kitchenaid Service manual.

http://www.kitchenaidparts.be/centers/servicemanual/mixer.pdf

You may have to remove the Motor Housing and use a small screwdiver
to completely remove the brushes or all portions of them if they are broken.

Jul 30, 2011 | KitchenAid K45SS Classic Stand Mixer

1 Answer

I was using meat grinder attachment and stand mixer stopped running


I just got the same problem too. There was a little piece of fat in the meat and it stopped the grinder. I removed it but the attachment rotates a full turn and then stops. The same happens with other attachments even under practically no load.

Dec 02, 2010 | KitchenAid Food Mixers

1 Answer

KSM75 Mixer: I want a an additional bowl..what miodel do I need...


For Accessories for the KitchenAid in the USA refer to http://www.kitchenaid.com/flash.cmd?/#/category/38/

Otherwise refer to http://www.kitchenaid.com/flash.cmd?/#/page/customer-service-contact/ for customer service.

You can also try for United States, District of Columbia, and Puerto Rico, call toll-free 1-800-541-6390. For Canada toll-free 1-800-807-6777.

May 16, 2010 | KitchenAid KSM75 Mixer

1 Answer

Stopped running. I failed to secure the bowl and it came loose while running. I stopped it quickly but the mixer stopped running after that.


there is a thermal fuse inside tapped in-line of AC cord .if it was under a heated load it will blow non resettable . need a test meter to check for continuity .electrical flow . with machine not plug in , these items are very small .187 diameter and are crimped in line of AC cord , these are going to cost about $8-10 dls us can be bought @ Radio Shack rating should be about 8-10 amperage , good luck >^.^<

Mar 19, 2010 | KitchenAid Food Mixers

1 Answer

In middle of kneading dough, the machine stopped! I noticed that the gears that connect the bowl to the machine, stopped turning, when machine goes on, it makes a noise, but nothing turns.


Hi HENNY346. Your Bosch mixer is belt driven and from the description of your mixer’s symptoms I suspect that the drive belt has come loose or failed completely so it stopped driving the dough hook. You say that when you turn the mixer on, it makes a noise, which may be the motor running without any load, but your description of ‘noise’ is very vague.
The good news is that you should be able to diagnose and fix this quite easily (OK, maybe with a little effort) by yourself, if you are a DITY type person, feel adventurous, and your mixer is not under warranty.
Here are links to two online parts vendors for your Bosch mixer that also provide an exploded view diagram along with part names, numbers and prices. They are: Cook's Quarters and AppliancePartsPros.com It can be very gratifying to go “under the hood”, figure out what’s wrong and fix it yourself. Good luck , I hope this helps. Howard, Burke, VA
If this solution was helpful, please rate it, thanks! – hslincoln

Feb 23, 2010 | Bosch MUM6612 Universal Series Mixer

1 Answer

Motor runs, beater stopped rotating. Some gear sounds heard before it stopped. Beater will not turn at any speed setting.


drive gear or shear pin stripped. Common on this model. Return to repair centre. Expect to pay approx $150.00 to repair, sorry.

Sep 14, 2009 | KitchenAid KSM150PS Artisan Series Stand...

1 Answer

Mixer has just stopped


On the newer A200s, there is a reed switch behind the solid portion of the bowl gaurd. On the cage portion there is a magnet embedded in a plastic holder. Without it, the mixer won't run.

Hobart part # 438525

http://www.hobartlink.com/extranet/extranetmanualsandcatalogs.nsf/57866D624A678E7385256CB0007232DA/$File/F-19357%20(05-95).pdf

Apr 04, 2008 | Hobart A200 Stand Mixer

Not finding what you are looking for?
KitchenAid KSM75WH WhiteTilt-head Stand Mixer Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Food Mixers Experts

Appliance engineer

Level 2 Expert

87 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a KitchenAid Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...