Question about Visonik Dual Bass Box with Amplifier Car Audio Amplifier

Open Question

Car amp is in protect mode red light on, protection light not on. speakers are thumping fast no music.

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: VB101PK REV 13, AMP WITH SUBWOOFERS

you may have to much speaker for the amp or one of ur wires could be crossed

Posted on Mar 17, 2008

Ad
  • 7 Answers

SOURCE: Thumping speakers - no power light is on - wired correctly

the amp is going into protect mode due to something wrong in the amp or some thing in the wiring to it ooh yea if you are getting 18v power to the amp that is way to high it should not be higher then 15v if the amp is in protect mode it will not play at all.

Posted on Nov 02, 2008

  • 631 Answers

SOURCE: Amp Power light will not go on. Protection light is lit- Thump sound in speakers

It probably has shorted output transistors. To eliminate other possible causes, read through the following page.

Amplifier in Protect Mode - Troubleshooting

Let me know if you have any other questions.

Posted on Nov 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Tc 8001 red light


on some amps there is a duel light. red and green usually. red means it is in protect mode or you didn't hook up your remote wire. if in protect mode, it could mean a number of things. did you hook it up with speakers and everything?

Mar 01, 2012 | MTX Thunder® TC8001 Car Amp

1 Answer

Protect mode


Protection circuit.
Checek the wiring of the amp and speakers, don' forget to look for shorts at the speakers. Make sure no wires are touching each other

Apr 30, 2010 | Volfenhag 1600 WATT CHROME AMP AMPLIFIER 2...

1 Answer

No sound coming out of speakers something is wrong with the receiver


check if it goes to protection mode on power on. see to it that speaker selector switch is set.

Is your speakers connected properly?

Is your music source ok?

Do you hear a click after you switch on the power? the click indicates that the time-on delay transfers the amps output to the speakers which prevents thumps going out to the speakers.

Once it goes to protection mode you need to have it serviced. This is due to a fault in one of the amps and that it protect the speakers from further damage.

Aug 17, 2009 | Onkyo TX-SR502 Receiver

1 Answer

Power light turns from green to red protect mode and then there is no sound coming from my speakers


there are 2 reasons for it to be going into protect mode 1 is heat 2 is the load on it. if it is going into protect mode soon after it starts there is a problem with the speaker. if it is after it has been on for a while it is that the amp itself is overheating. hope this answers your question

Apr 27, 2009 | SPL Audio Phantom DK2-1000 Car Amp

1 Answer

Protection Light Comes on


your amp isnt getting enough power to it you may need to install a compacitor unit

Mar 23, 2009 | Sony NTX-2136 DHD 2Channel Car Amplifier...

1 Answer

Protection Light Comes on


Sounds like you have an ohm problem, Tryy hooking the positive from one speaker to the negative on the other speaker. Then hook the negative from the first speaker to the negative on your amp and the positive from the second to the positive on the amp this will drop your ohm load and the amp should stop going into protection.

Mar 08, 2009 | Sony Xplod XM-1652Z Car Audio Amplifier

2 Answers

My amp stays in protection mode


Does it go into protect in the vehicle if you disconnect the speaker wires from the speaker terminals of the amp?


Nov 29, 2008 | Sony XM-2002GTR Car Audio Amplifier

1 Answer

Thumping speakers - no power light is on - wired correctly


the amp is going into protect mode due to something wrong in the amp or some thing in the wiring to it ooh yea if you are getting 18v power to the amp that is way to high it should not be higher then 15v if the amp is in protect mode it will not play at all.

Nov 02, 2008 | Visonik Dual Bass Box with Amplifier Car...

1 Answer

Amp Power light will not go on. Protection light is lit- Thump sound in speakers


It probably has shorted output transistors. To eliminate other possible causes, read through the following page.

Amplifier in Protect Mode - Troubleshooting

Let me know if you have any other questions.

Oct 31, 2008 | Visonik Dual Bass Box with Amplifier Car...

3 Answers

Red LED "Protection Light is on" What is the problem


The red light means the amp is in protection mode. A few things can cause protection mode..... First disconnect the subs completely from the amp, and turn it on, if it powers up you have blown subs. Also try checking the main power wire at the battery...sometimes the current your meter is seeing is backfeeding from the remote wire, so your main power line could be blown at the fuse under the hood. hope this helps

Jul 17, 2007 | Crunch BlackMaxx BMX2250 2 Ch 1000W Amp...

Not finding what you are looking for?
Visonik Dual Bass Box with Amplifier Car Audio Amplifier Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Visonik Car Audio & Video Experts

Tygh Duval
Tygh Duval

Level 2 Expert

300 Answers

Joe Alexander
Joe Alexander

Level 2 Expert

65 Answers

Jerry Umali

Level 3 Expert

979 Answers

Are you a Visonik Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...