Question about Kenmore Washing Machines

1 Answer

How to install part number 8577376 for kenmore washer

How do you install this seal?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

What is the seal for ? Door ?

Posted on Nov 29, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Kenmore front load washer model number 417. It's been smelling after use.

The rubber seal /boot can be replaced If it's really bad but you will need to clean soap dispenser pull it out all the way buy washer magic to clean rubber seal and door also buy afresh put two tables in tub run longest and hottest cycle with extra rinse once cycle finishes than take half bottle of washer magic and pour into soap dispenser run another cycle if still bad do it all again

Apr 23, 2016 | Kenmore Washing Machines

1 Answer

How much does it cost to replace the seal on a Kenmore top-loading washer?

Please check this site and link from where the seal can be purchased and gives you an idea to replace the same.

click on:Door seals

Jun 27, 2012 | Kenmore Washing Machines

2 Answers

How much does it cost to replace the rubberseal

Hello, Welcome to FixYa.

Hopefully the info below will supply you with the assistance to get the door seal your enquiring about. They should have anything you need. (provided the numbers in your post are accurate "45986"...though the complete number should be on the tag inside the door opening of the washer. ELITE&modelDesc=RESIDENTIAL-WASHER&blt=11

The gasket/bellows is part number 8182119 and sells for around $100-$110US. The cost to install will vary on how it's done and by whom of course.

Thank you for choosing FixYa. Please take a moment to rate the assistance you received here today and good luck.


Macmarkus :)

Aug 14, 2011 | Kenmore Elite 45986 Front Load Washer

1 Answer

I came across a Kenmore Oasis washer-model# 11027062601 thats noisy on spin.Do you know what they have for a center bearing & seal setup? Rene

First, see the Sears Parts site for your washer:

Enter your model number (110.########) and you'll see a set of diagrams with all the parts / costs for the washer:

Also see the following Whirlpool Service Manual for their Cabrio washer. It's basically the same as the Kenmore Oasis.$FILE/8178583.pdf

Between the two sites, you should be able to determine what the center bearing and seal setup is.

Aug 10, 2010 | Kenmore Oasis HE 27062 Top Load Washer

1 Answer

Kenmore 80 Series washer leaves brown grease marks

Remove the agitator and check the shaft seal underneath the plastic drive block at the top of the shaft. Move the shaft in different directions to check the condition of the top bearing. If none or very slight, replace the seal at the top of the shaft supporting post. Clean any grease that is outside of the seal when you are done. Be sure to not damage the seal surface on the shaft when removing/replacing the seal and pre-grease the new seal's inner lip before installing.

Nov 15, 2009 | Kenmore 22422 Top Load Washer

1 Answer

Front Rubber Washer

Here ya go. Follow the steps outlined in this link:

If you have questions along the way, please let me know. If you need to know where to purchase a new door seal, also let me know. Post back with your model number for clarification. I hope this helps you.

May 01, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

Kenmore laundry center stacked washer/dryer washer tub shakes almost violently on spin cycle.I may have changed setting during spin cycle.Tub is off balance.The appliance cabinet is balanced and on a solid...

Head over to the manufacturer's website. and enter your full model number for an expanded parts diagram and ordering information.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Apr 11, 2009 | Kenmore Washing Machines

1 Answer

Torn door seal on front loading washer

My husband used super glue on the tear and for now the washer is not leaking.

Mar 25, 2009 | Kenmore HE2 Plus Front Load Washer

1 Answer


i have a kenmore elite washer the red lite is lit on controlles locked how do i solve this

Mar 22, 2009 | Kenmore Elite 45986 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Sal DeAngelo

Level 3 Expert

2290 Answers


Level 3 Expert

5537 Answers

Ed Mac

Level 3 Expert

731 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides