Question about Dacor ECS130 Epicure Electric Single Oven

Open Question

Dacor single oven wall unit does not heat in two modes. Can reach a temp of 295.

The oven will not heat 290 on the bake mode and the convection/bake mode. The cleaning cycle did not clean the oven either. So, I am thinking about trying to find the reset button, turning off circuit breaker to reset the oven, or consider replacing the two heating elements? What do you think?

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

6ya.com

Download 6ya

6ya.com

Need repair answers fast Use 6ya to...

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: dacor oven ECPS127S will not heat after self clean

the problem was fixed by opening the panel between the oven cavity and the touch panel just behinf the door. you can look through the grill but to trip the reset you must unscrew the panel. you will find the reset back behind the wires Looks a red button nestled on top not very open but it should be there> i do have to say i found a step by step description on this site. but right now i can't tell you who exactly he was.

Posted on Feb 24, 2008

  • 2 Answers

SOURCE: Oven won't heat.

Thanks for the tip. Had the same problem, everything seemed to work except for the heating elements. Removed the vent cover inside the door just below the control panel. Found the reset button and also found one of the large black power wiires had come loose from its connector. Turned off the power at the breaker box, checked for voltage with a meter and re-attached wire connector with insulated pliers. Oven works now. Lets call this failure "poor workmanship at Dacor".

Posted on Feb 03, 2009

dmftrucker
  • 1922 Answers

SOURCE: Dacro Wall oven (electric) does not heat past 345 degrees on bake or convection bake but broiler works and bottom oven works fine (for bake, convection bake and broil).

it could be the oven temp sensor rod located near the top of the inside of the oven,or possibly the bake element has a hot spot on the element and can no longer pass enough current thru this spot to correctly heat to your settings a hot spot on the element will look discolored in this area

Posted on Jul 29, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0 Answers

How do you access and replace the hidden oven element in a Electrolux/Frigidaire Galley 30 single electric convection wall oven? Model # FGEW3065KWA

Apr 09, 2017 | Ovens

1 Answer

Bake Element
I would start by checking the temp sensor of the bake temp settings. Pull it and its most likely bad your thermostat control, also did you ohm out the element before installing it i have bought many new bad ones as well. anything else just ask.

Apr 05, 2014 | Jenn-Air 27 in. Electric Single Wall Oven...

1 Answer

Dacro Wall oven (electric) does not heat past 345 degrees on bake or convection bake but broiler works and bottom oven works fine (for bake, convection bake and broil).
it could be the oven temp sensor rod located near the top of the inside of the oven,or possibly the bake element has a hot spot on the element and can no longer pass enough current thru this spot to correctly heat to your settings a hot spot on the element will look discolored in this area

Jul 28, 2012 | Dacor Ovens

1 Answer

My Jenn Air oven W27200B displays F2 error any solutions? Also one of the burners would hang- one worked and the other didnt.
HI. this is a failed oven temp sensor or relay board.

Oven temp sensed; over 600F sensed by control in time of day mode, bake mode, or over 900F sensed in clean mode.


Ohm test the oven temperature sensor, if OK, change power relay board.

Sep 14, 2009 | Jenn-Air 27 in. Electric Single Wall Oven...

2 Answers

My dacor oven model ECS130SBK is very slow to heat. Sometimes reaching the desired temp. after a long wait. Sometimes it never gets there.
I found the bottom element was not getting any power by using a volt/ohmmeter and a test method described elsewhere. (Shut off power, hold down COOK TIME while turning on power. then within 30 seconds press each mode you want to test and only that element/fan/etc will turn on. Cancels by itself after 30 sec.)


I traced the wire back to the relay (wire checked good) and there was no power getting through the relay although it clicked. Removed the relay board to replace it and found a cold solder joint on the "out" terminal with obvious past arcing carbon. Cleaned and soldered the pin and the oven now works normally.
WHY THE SLOW TO HEAT? The oven turns on all the elements to preheat faster and when it reaches your set temp it beeps and now only turns on the element you selected to maintain the temperature. (Bake or Convection) Our malfunctioning ovens would then cool since the element is not working properly and it must go back into preheat and keep cycling.
BY THE WAY- Don't ever use 4 hours on self clean it kills the boards and/or display. I also put a house fan in front of the oven and blow it into the lower grill to take away some of the heat on the two boards. Learned the hard way!

Jun 08, 2009 | Dacor ECS130 Epicure Electric Single Oven

2 Answers

Dacor oven takes long time to heat.all modes
DACOR DIAGNOSTIX BABE !!!

Jun 08, 2009 | Dacor ECS130 Epicure Electric Single Oven

1 Answer

Bosch HBN 642 -- single oven cycles and doesn't get above 325
WHAT WAS HAPPENING AT 1ST YOUR HI-LIMIT TERMAL SAFETY OR OVEN TEMP SENSOR FELT THAT THE OVEN WAS GET TOO HOT AND SEIZING OPERATION UNTIL SAFE TEMP WERE OBTAINED THIS IS GENERALLY A FAULTY OVEN TEMP SENSOR. I WOULD ADVISE YOU TO CONTACT A CERTIFIED TECH TO LOOK AT IT AND P.S. DON'T MENTION THAT YOU TOOK THE MACHINE APART MOST SERVICE COMPANIES WILL NOT SERVICE THE MACHINE IF IT BEEN TAMPER WITH BY THE CUSTOMER DUE TO INSURANCE AND LIABILITIES

May 28, 2008 | Ovens

1 Answer

My Dacor wont heat, broil or convection after self cleaning. No heat but everything else works The bake, broil, and convection elements on my Dacor CPS130 electric wall oven will not heat.  The oven has...
like another person stated-from the front behind the door, take off the 6 screws and the cover by the latch. there is an "oven hi temp limit switch" It is crome with 2 heavy black wires connected to it. On the back side of this is a small red button which will reset the limit switch. I had the same issue (everything worked except the any of the heating elements) and quickly resolved.

Jan 07, 2008 | Ovens

1 Answer

Convection Over with Dacor Millennia
We have the same issue anc alled Dacor. I seems as there is a problem with the oven as it was built with a faulty or missing temp control part. They have a fix for this problem by installing a temp control kit. you need to work through the warrantee group

Dec 20, 2007 | Dacor Millennia MOV130 Electric Single...

1 Answer

Dacor Oven - convection fan stays on while on "bake" setting
Question: does the unit appear to hold the correct temperature? Most convection units only turn the heating elements on and off...not the fan. If the unit is reporting operating temp and then taking other direction...and it is cooking right...you're done.

Nov 14, 2007 | Dacor ECS127 Epicure Stainless Steel...

Not finding what you are looking for?

View Most Popular

ECS130 Epicure Electric Single Oven

  • Ovens

Related Question

How do you access and replace the hidden oven element in a Electrolux/Frigidaire Galley 30 single electric convection wall oven? Model # FGEW3065KWA

  • Ovens

Open Questions:

0 Answers

On bake - oven doesn't heat up but broil will come on. Temperature will not get up to set temperature and top of food burns. Manual reset button would not reset. No obvious breaks or faults in element. Haven't used an ohm meter.

Oct 08, 2015 | Dacor ECS130 Epicure Electric Single Oven

0 Answers

The decor ECS130 SCH door does not spring closed. Can I adjust something or is a new part needed?

Apr 27, 2014 | Dacor ECS130 Epicure Electric Single Oven

0 Answers

dacor oven beeps f8

Apr 13, 2014 | Dacor ECS130 Epicure Electric Single Oven

0 Answers

Dacor range does not work

Mar 17, 2014 | Dacor ECS130 Epicure Electric Single Oven

See all Dacor ECS130 Epicure Electric Single Oven Questions

Dacor ECS130 Epicure Electric Single Oven Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

Dacor ECS127 Epicure Stainless...

Dacor ECS230 Epicure Electric...

Dacor ECS130 Epicure Electric...

Dacor ECS127 Epicure Electric...

Dacor MCS130 Millennia Electric...

Top Dacor Ovens Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

ashburton

Level 3 Expert

417 Answers

Jaime Hernandez

Level 3 Expert

2315 Answers

Are you a Dacor Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
. ECS130 Epicure Electric Single Oven...

ECS130 Epicure...

Loading...