Question about Tools & Hardware - Others

Open Question

Can not open bostitch model b5 stapler - Tools & Hardware - Others

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
efs_perpends
  • 1996 Answers

SOURCE: Unable to figure out how to open the door for

I can't locate that model, but if you go here and enter the full model number you'll be able to download an instruction manual that will explain how to load staples.

I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread.
If I've managed to answer your question or solve a problem, please take just a moment to rate this post....thanks!

Posted on Sep 05, 2009

Ad
radar001
  • 1051 Answers

SOURCE: I can' find staples

Home Depot and Lowes have them.

Posted on Nov 22, 2010

  • 1 Answer

SOURCE: There is a Stanley bostitch model B2000 stapler in

The person that asked this is probably long gone, but in case anyone else comes across this... I had the exact same problem when I dropped this same stapler today and the spring came out. After examining it for a bit, I realized where the spring had to go and fixed it.
Open the stapler the same way you would as if you were replacing the staples and look at the top piece, towards the back. There will be an elongated black hook here to attach one end of the spring. The trick is where you route the spring after that... look towards the front end of the same top piece, and you'll see 2 holes in the metal. You need to push the spring up through the first hole, then pull it back down through the second hole (you may want to use a straightened paper clip to snag the spring so you can pull it through that second one), and only then do you attach the other end of the spring to the hook in the sliding metal piece that advances the staples in the staple holder.
And that's it!

Posted on Dec 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Open and load staples b660


Hold on to the chrome part near where the staples come out and lift up on the top plastic part. There is a video link on the Bostitch site to the right midway down the page
Stanley Bostitch No Jam Premium Stapler B660 Black

Feb 08, 2015 | Stanley Bostitch B660-BK: NoJam Full Strip...

1 Answer

Bostitch stapler stuck


Hello, Go here to download the operators manual to help you with troubleshooting this stapler. It also will have a number for tech support so you can call for help. Bostitch Office Products Staplers Pencil Sharpeners Hole Punchers Tools...

Jun 06, 2014 | Stanley Bostitch B8 Electric Stapler

2 Answers

Bostitch electric stapler wont open


Hello, Go to this website for support number and downloading of the operators manual for the model of stapler. Bostitch Office Products Staplers Pencil Sharpeners Hole Punchers Tools...

May 01, 2014 | Stanley Bostitch B8 Electric Stapler

1 Answer

How do I put the Bostitch B660 stapler back together?


MAYBE THIS IS USEFUL http://www.ereplacementparts.com/bostitch-21680b-industrial-fine-wire-stapler-parts-c-29443_29444_29449.html

Apr 02, 2012 | Air Tools & Compressors

1 Answer

I inherited a Bosch T31 bradder and stapler. Couldn't get any help at Home Depot chosinga nails. Bought Porter Cable 16 Ga. 1" finish nails (PFN16100-1). Released arm and slid the nail carrier...


BOSTITCH T31-1 stapler & T31-2 STAPLER and NAILER. Both use 18 gauge (very fine gauge wire). Try using 18 gauge Bostitch staples (used in BT model bostitch staplers). Good Luck

Feb 03, 2011 | Stanley Bostitch N80CB Coil Framing Nailer

1 Answer

How do I replace the staples in Stanley Bostitch B310HDS? I cannot seem to figure out how to open it.


"The staples load from the rear of the stapler. At the back end of the is a piece of black plastic that extends beyond the end of the stapler. This device holds the staples inside the stapler. To open the area where the staples are placed, push this extended button and lift up on it. The spring device that holds the staples inside the stapler will then slide out. Place a new strip of staples inside the stapler on top of the two metal guide rails. Then insert the spring device to lock the staples in place. The stapler is now loaded and ready to work. " hope this helps you out

Jan 06, 2011 | Stanley Bostitch 00540: 00540 AntiJam ?...

1 Answer

Door springs, part no. H286, for a Bostitch H2B stapler


Parts for the Bostitch H2B Hammer Stapler can be purchase from MJS Floorcoverings Manfield Brisbane

Dec 16, 2009 | Stanley Hand Tools

Not finding what you are looking for?
Tools & Hardware - Others Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tools & Hardware - Others Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Brad Brown

Level 3 Expert

16010 Answers

J.D. Browning
J.D. Browning

Level 3 Expert

2760 Answers

Are you a Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...