Question about Car Audio & Video

1 Answer

Don't know to conneect my amplifier connecting firdt a soundstream ecualizer

I dont have the connection diagram of my gp880.4 crunch amplifier, I want to connect a soundstream ecualizer first

Posted by on

  • Anonymous May 25, 2009



1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

What are you running in to your amp? If it's a CD player or radio, find the wires from them, disconnect them from the amp and connect them to the equalizer, then connect the equalizer to the amp.

Posted on Jul 12, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I've had two soundstream rubicon 1.1600D amp's and they both worked for a while then the amp started to kick off and on. No fuses were blown, and the ground was fine. Any suggestions would be appreciated.

Sounds like a loose power connection? Check All connections, also make sure the impedance is correct 4ohm 8omh 16 ohm the speakers need to match the amplifiers output to work properly. ...

Feb 21, 2015 | Soundstream Car Audio & Video

1 Answer

Noise after amp installed

Check its wiring. There is many things to consider when wire it with; otherwise audio will be distorted at high level volume. It should be done according to wiring diagram. Wiring diagram to many sets are illustrated by the site give below. Check it.

Jul 05, 2014 | Crunch Car Audio & Video

2 Answers

Connecting s Soundstream PXW10 Subwoofer

Connect the subwoofer the following way if you have a separate subwoofer out in your amplifier (ie. 3 channel amplifier). Ones on the left are -1 and +1, the ones on the right are -2 and +2. I think you have to join +1 to -2 according to this diagram and then join -1 and +2 to the subwoofer out in the amp. I took this diagram from the following website but check with someone else as well.

If you do not have a separate subwoofer out in your amp you may use a multichannel crossover amp and use the rear outs for the subwoofer connection the way it is described in the following website.

Hope that this helps.
Udai De Silva

Mar 16, 2014 | Car Audio & Video

1 Answer

Amp heating up

__Amplifier Heating__


1-insufficient air circulation to the amplifier where installed
2-incorrect speaker connection (out of phase)
3-overvoltage of amplifier
4-insufficient power to the amp
5-ground cable not contacting properly
6-unbalanced OHM loads (different ohms speakers driven at the same time
1-change location of amplifier
2-connect all (+) and (-) of speakers to their corresponding connection on the amplifier
3-the input sensitivity (gain) of the amplifier is to high in relation with the headunits output voltage. match output of unit to input of amplifier
4-the cable is to thin to provide adequate current to the amplifier or the car battery is on its way out
5-secure ground cable and make sure there is always a clean secure ground to the chasis. ( checking power and ground cables should be done on a monthly basis due to the vibration factor in vehicles
6-use speakers with the same ohm load

Hope this helps. for further help let me know what equipment you r using and how they r connected.

Dec 26, 2013 | Soundstream Car Audio & Video

1 Answer

I do not have the manual. I need wiring diagram how to connect to the power and speaker.

if you need a manual to hook up an amp, you probably shouldn't be doing it yourself.

Sep 13, 2010 | Crunch PZI250.2 Car Audio Amplifier

1 Answer

Soundstream XBP-10 Installation

Dude I sat down and made up a diagram for this and I cant get the site to let me upload it. If you can get a generic email quick from yahoo or something and get back to me I will email it to you.

Dec 22, 2009 | Soundstream Car Audio & Video

1 Answer

Soundstream ribcom500

they should be able to help and have all the spare parts.

Nov 07, 2007 | Soundstream VGA400.2 Car Audio Amplifier

1 Answer

Soundstream ribcom500

You can get the schematic from SoundStream. If you get the schematic and need help, email it to me at:

If the amplifier does nothing, post the DC voltage on each of the pins of the SG3525 (or whatever IC they're using in the supply). Use this as a template:

Pin 1:
Pin 2:
Pin 3:
Pin 4:
Pin 5:
Pin 6:
Pin 7:
Pin 8:
Pin 9:
Pin 10:
Pin 11:
Pin 12:
Pin 13:
Pin 14:
Pin 15:
Pin 16:

Nov 07, 2007 | Soundstream Davinici Car Audio Amplifier

3 Answers

Amlifier not working

connect your remote turn on and your problem will be solved

Sep 23, 2006 | Crunch BlackMaxx BLX2000D Car Audio...

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4844 Answers


Level 3 Expert

75797 Answers

The Knight
The Knight

Level 3 Expert

74106 Answers

Are you a Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides