Question about KitchenAid 24 in. KUDI01FL - Multiple Color Built-in Dishwasher
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Blinking Clean Light
Posted on Jan 23, 2009
If the clean light flashes 7 times, pauses, then repeats...
When the dishwasher doesn't sense a water temperature increase, it will stop working and lock the functions (clean light flashes 7 times, all buttons are non responsive). It does this as a safety in case the element is broken and feeding electrical current into the water.
To resolve this you will have to reset the console. Do this by closing the door and press these buttons in sequence...
-high temp wash
-high temp wash
...all the lights will turn on briefly and the machine will start a diagnostic cycle. You can press cancel or let the diagnostic cyle finish (1-2 minutes).
You should now be able to run the dishwasher as normal.
If the issue returns, you could have a problem with the heating circuit (ie. element, thermostat or wiring). It rarely happens but it could also be the door switch not engaging properly when the door is closed (slightly bend the door latch down making sure it doesn't hit the door when you close it).
Posted on Mar 02, 2009
Great job walking through the possible causes! Hey, it is time to check the heating element itself. First visually, looking for brakes and then feeling for "bubbles" on the round element rod. Also see if it moves excessivly when you wiggle.
If no problem obvious, after you disconnect the dishwasher from power, use a multimeter to check for resistance (Ohms) If none, look for broken (heavy guage) wires and replace what's broken - probably the element itself.
If the element checks out good, suspect the thermistor then the controller/PCB.
Good Luck! Please report back what you find, OK?
Posted on Apr 11, 2009
you have to hit heated dry and normal and toggle these till all the lights light up. then hit cancel . you are going to have to turn the power of and slide the dishwasher out and look directly behind the dishwasher you will see that a wire off of the heater is more than likly burned of repair the wire you should be fine. replug dishwasher in after wire is repaired. if you do not have a burned wire you have a bad heating element replace the element.
Posted on Apr 14, 2009
I tried the following sequence, as recommended on a similar blog and it worked!
Quickly press :
Hi Temp Scrub
Energy Saver Dri or Heat Dri
Hi Temp Scrub
Energy Saver Dri or Heat Dry
All lights should come on
then clear and revert to cycle.
Posted on Aug 10, 2009
Tips for a great answer:
Dec 25, 2014 | Maytag Dishwashers
on Apr 25, 2010 | Maytag MDB8959AW Builtin Dishwasher
Oct 02, 2014 | KitchenAid Dishwashers
Feb 04, 2014 | KitchenAid KUDE70FXSS Builtin Dishwasher
Nov 28, 2013 | KitchenAid KUDE70FXSS Builtin Dishwasher
Aug 24, 2011 | KitchenAid 24 in. KUDI01FLSS Stainless...
Jul 01, 2011 | KitchenAid 24 in. KUDS01FLSS Built-In...
Mar 04, 2011 | KitchenAid 24 in. KUDI01FLSS Stainless...
Feb 01, 2011 | KitchenAid 24 in. KUDI01FLSS Stainless...
Feb 25, 2009 | KitchenAid 24 in. KUDI01FLSS Stainless...
36 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: