Question about Bosch Axxis WTA 4107 Electric Dryer

1 Answer

Every time I turn the dryer on it trips the electric. do you know where the switch is to stop this on my hotpoint ctd00 dryer

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 121 Answers

Sounds like the element is gone short curcuit . if the power did not trip it would go bang so be careful .these things can be dangerous .have known the cabinet to be live when earth not conected in the plug...farr64

Posted on May 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Our Hotpoint ctd00 keeps tripping the fusebox, we


Disconnect the heater thermostats by poulling a wire off each stat, and then try it, if it still trips, then could be faulty motor.
The stats are located at the rear of the dryer, behind removeable cover.

Mar 25, 2010 | Hotpoint Dryers

1 Answer

CTD00 drum does not turn,heating OK,belt OK,motor OK


you have a bad motor,most likely.

Mar 03, 2010 | Dryers

1 Answer

Why is my hotpoint ctd00 condenser dryer leaking water from underneath and turns the electricity off''


you are not on your own we have the same problem we are going to convert back to the old fashion tumble dryer

Dec 23, 2009 | Hotpoint Dryers

1 Answer

Hotpoint tumble dryer CTD00 timer


It is not a difficult job...the thing to keep you out of trouble is to make sure you get the right timer switch, then remove one wire at a time.
Remove one wire from the old timer and put it on the new timer, there is not that many wires for your timer.
I will include these two websites for parts and further help:
http://www.partselect.com/
http://www.appliancepartspros.com/index.aspx
Both also have chat assistance 24/7.
Good luck,
I hope this helps

Nov 05, 2009 | Hotpoint Dryers

1 Answer

Safety Trip


On the heater there will be a cut-off switch with a small hole where you can stick a needle in until you hear a 'click'.

Jul 14, 2009 | Hotpoint Dryers

1 Answer

Drying Problems with a Hotpoint CTD00


There is a thermal fuse at the back that you must check. The thermal fuse can be tested using a multimeter.
If the fuse is ok, then check the heating element , the temp probe, wiring harness to heating element and temp sensor, and if there is nothing in there , then test control timer board.


Regarding parts, contact the seller here to purchase parts. (here in UK).

Apr 27, 2009 | Hotpoint Dryers

1 Answer

DRUM NOT SPINNING....and a burning smell


Motor going bad. Run windings inside are burneded up.  Start windings are ok. replace motor.

Jan 07, 2009 | Hotpoint TDC32 Electric Dryer

2 Answers

Hotpoint aquarius CTD00 dryer


how many fuses are there in a hotpoint tumble dryer CTD00 aquarius I know one is in the plug is there another one if so where is it?

Aug 18, 2008 | Dryers

2 Answers

Hotpoint condenser dryer ctd00


change the drive belt. evidently the belt has stretched to the point the belt tensioning device can no longer do its job. when you change the belt make a diagram of which way the belt is reaved through the tensioning device. if you don't you'll be back here asking how to arrange the belt.

Jun 19, 2008 | Hotpoint TDC32 Electric Dryer

1 Answer

Dryer cutting main power off after acouple of seconds


your heating element is the most likely cause of this. will need replacing

Nov 18, 2007 | Hotpoint TDC32 Electric Dryer

Not finding what you are looking for?
Bosch Axxis WTA 4107 Electric Dryer Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Dryers Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Lawrence Oravetz

Level 3 Expert

9324 Answers

MightyMikeJr

Level 3 Expert

388 Answers

Are you a Bosch Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...