Question about Homelite Garden

1 Answer

I have a homelite chain saw that the bar oil is not dispenseing

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

May be oil port on saw clogged. Remove side cover, remove bar and chain. Remove giude plate if equipped. Check to see if small oil hole on saw is open and clean. You can start the saw with side cover removed to see if oil is coming from oil hole or not. If it is coming from oil hole when running the problem is most likely dirty bar .If bar is dirty check to see that groove is clean and the oil hole along the edge of bar is clean also. The hole is at same end of bar that attaches to saw.

Posted on May 09, 2009

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 211 Answers

SOURCE: husqvarna chain saw, model 455 will not oil properly bar and chai

hi cindilou50
check the oil filter from the oil tank,the oil line ,the worm gear and the oiler under the clutch.Clean the ways where the oil goes with compresed air.(after you fill out the oil tank)Also check the oil hose.

best regards savumihai71

Posted on Dec 01, 2008

Editor925
  • 285 Answers

SOURCE: homelite chain saw --first time user--do you mix

In the compartment closest to the chainsaw bar, you need to fill this with chain and bar oil. Any good name brand will work fine.

In the other compartment you need to add a mix of petrol and oil in the ratio specified for your saw. If unsure, 25:1 petrol/oil ratio should be ok.

Posted on Jul 21, 2009

  • 4088 Answers

SOURCE: just got a homelite 33cc

Yes you do! The ratio is 50:1 fuel to oil. Be sure to use a modern synthetic saw oil available at home centers, hardware stores, and saw dealers. Be sure to use fresh fuel and mix the two in it's own container. Be sure to shake the container thoroughly each time just before refueling to prevent oil starvation in the engine. Don't make up more than one gallon at a time unless sawing is your business. Hope this helps!

Posted on Dec 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a oil ajustment for the bar oiler on a homelite chain saw


Homelite XL auto oiler - YouTube

? 2:44
https://www.youtube.com/watch?v=PnNTJ3xI_wo
Mar 24, 2012 - Uploaded by 343HFD
Refurbished, carb cleaned/adjusted, new filter, fixed automaticoiler. Anyone know the nut size for the bar ...

HOW TO REPAIR CHAINSAW OILER - YouTube

? 6:38
https://www.youtube.com/watch?v=kmUkieIP-vw
Jan 20, 2012 - Uploaded by gregthegardener
lf your chain saw isn't lubing the chain it can cause serious chain ... How to Replace the Bar & Chain Oil ...

Dec 03, 2015 | Homelite Garden

2 Answers

How can I adjust the oil flow to the bar of chainsaw?


Look-up the UT-43103 IPL. There is no provision to adjust the oil flow. Suggest checking the oil lines for loose or broken areas; also could replace the oil pump. These are very inexpensive parts. here is a link to the parts list and source for the parts.

Homelite UT43103 Electric Chain Saw Parts

Dec 06, 2014 | Homelite Garden

1 Answer

What type of GAS and OIL need for the chain saw?


Hi gjoun...
You will need "Chain and Bar" oil to lube the chain and bar. Special oil made just to lubricate the chain and bar as the chain is running.
For the engine you can use the low grade of gasoline...and 2 cycle oil.
Fuel mix...50 to 1 = 1pint of 2 cycle oil to 6 gallons of gasoline.
Please take time to rate me

Sep 19, 2011 | Homelite ZR10926 16 Chain Saw

1 Answer

Does a homelite chain saw have a crank case youn put oil in homelite xl


Hi, it needs a two cycle mix at a ratio of 25 to 1 in the fuel tank and bar and chain oil in the oil tank. Hope this helps, regards Phil.

May 31, 2011 | Homelite Garden

2 Answers

Bar oiler dos'nt work may be plug???


Hi larsgordy,

To unplug your oiler, first remove the chain brake cover, bar and chain. Then clean thoroughly aroundthe inside. Clean the saw oil hole and groove and all holes and passages on the bar. Run the saw and see if that did it.

If not, then make a slender hook that isn't sharp and put it in the oil filler hole and grab the oil line and pull it out. clean it and check it for holes or cracks. If damaged you'll have to replace it. Continue through the passages, cleaning and checking for damages.
Here is a diagram from erplacement parts that shows you the breakdown of your saw: http://www.ereplacementparts.com/homelite-ranger-ut10926-33cc-1634-chain-saw-parts-c-18807_21362_37313.html

If you still have trouble after reassembly, then you'll probably have to replace the oil pump. It is located behind the clutch usually. You can locate it on the diagrams if need be.

I hope this helps. If it does, I'd appreciate your vote. Thanks,

Handie Andie

Apr 11, 2011 | Homelite ZR10926 16" Chain Saw

1 Answer

Chain oil tank full, feed channel behind guide plate clear, but no oil going to chain when running. This is a homelite 16.


There should be a oil adjusting screw on the bottom of your saw next to the bar beside the oil tank. Some models actually has the screw inside the tank. Drain the tank to make sure there isn't any debris clogging the hole where the oil feeds to the bar.

One way to check to see if the bar is oiling is:

1. Start the saw
2. Put a board, piece of cardboard or an uncolored old shirt in front of the bar
3. Press the trigger on the saw to allow the chain to circulate around the bar.
4. While keeping constant pressure on the trigger, look to see if there is a vertical line of oil on the piece of material you have placed on front of the bar. If the saw is oiling you will have a vertical line. If not adjust the oil set screw accordingly.

Nov 15, 2010 | Homelite ZR10926 16 Chain Saw

1 Answer

Need service manual for Homelite 16'' electric chain saw model UT 41320. Motor runs but chain stopped in middle of second cut.


chain is too tight on the bar or is lacking lubrication oil. loosen up the bar nuts and back off the chain tensioning screw a touch. make sure the bar oil reservoir is full and the chain is receiving oil when its running.

Oct 20, 2009 | Homelite Garden

1 Answer

Homelite chain saw --first time user--do you mix oil and gas--two compartments--is the first compartment for bar oil


In the compartment closest to the chainsaw bar, you need to fill this with chain and bar oil. Any good name brand will work fine.

In the other compartment you need to add a mix of petrol and oil in the ratio specified for your saw. If unsure, 25:1 petrol/oil ratio should be ok.

Jul 21, 2009 | Homelite Garden

2 Answers

The chain on my chain saw is slack.


The adjusting screw is usually found on the right side of the saw close to the bar, near the bottom. You will need to loosen the two nuts on the side that hold the bar tight. Loosen them until the bar lifts up and down (about 1/2") with your finger.

There should be a combination spark plug wrench and screwdriver that came with your saw. If not, use a slot screwdriverto tighten the chain while you hold the bar up with two fingers.

When adjusted properly, there should be no hanging slack in the chain when it is warm. It should rest just against the bar so that you can grasp it with gloves on and pull it toward you.

When it is tightened thusly, tighten the two side nuts while holding the bar up with two fingers. If you don't tighten the two nuts enough, it will loosen and the chain will have slack again shortly.

Remember that the hotter the chain gets, the looser it will be. Make sure your chains is getting plenty of bar oil. Never use regular motor oil.

Jun 08, 2009 | Homelite ZR10926 16 Chain Saw

Not finding what you are looking for?
Garden Logo

Related Topics:

407 people viewed this question

Ask a Question

Usually answered in minutes!

Top Homelite Garden Experts

roeb

Level 3 Expert

626 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Mike Squire

Level 2 Expert

420 Answers

Are you a Homelite Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...