Question about Miele Novotronic Premier 500 Front Load Washer

Open Question

Miele novatronic w916 water light keeps coming n

Miele novatronic w916 water light keeps coming on and machine will not complete wash cycle

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Bob Gemmell
  • 209 Answers

SOURCE: Miele washing machine model W713 front load - issues

If it is leaking from the waste pump area it may be blocked by a small piece of clothing like a sock or something similar! This will also cause it to take too long to complete a cycle. Remove the rubber hose onto the waste pump and check inside the hose and the pump, make sure the pump spins freely and that nothing is stuck in the hose pipes leading to the pump

Posted on Sep 13, 2007

Ad

SOURCE: miele novatronic w864 washing machine

There will be a small qty of water left after the wash. However if the compartment is full then the syphon tube is probably blocked.
Lift the flap of conditioner compartment, you will see a round 'post' in the middle to the rear of it. Pull this gently off. Give it a thorough clean and also take whole soap draw to sink and rinse. Where you removed the 'post' flush through with hot water. Replace the post (will click into place).
You should now be good to go.

Posted on Sep 21, 2008

  • 70 Answers

SOURCE: Miele W916 front-loading washing machine filling very slowly

Hi
There are two variant of this model one with normal fill hose and triple valve and one with waterproof system and triple valve. If you have change water proof hose (one with grey box on end) then it only leaves the triple valve.if waterproof hose is fitted be sure to order 110volt triple valve

Posted on Mar 29, 2010

  • 1 Answer

SOURCE: washing machine not spinning

I had a similar problem and about a week later it didn't wash at all.
Turned out the water inlet valve (one of the three) was faulty. The rubber seal/seat had a small hole and wouldn't open to allow water into the machine.
I wasn't prepared to pay the $213 for a new one so I went to our local appliance spares place and found one that was similar and used the rubber seal/seat from that to replace it. It was an electrolux single inlet valve part #360313 (from memory). Cost me $37. Could've got it for $22 delivered off ebay but I needed it asap.

Posted on Jun 05, 2010

  • 251 Answers

SOURCE: I have a miele novatronic w 1918 model washing

Hey - the inlet solenoid must be faulty - unless you have changed the wash options which is an outsider possibilty.

Posted on Jun 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Our miele w911 washing machine keeps stopping in the main wash cycle - red light above the tap symbol. What does it mean?


check that the water flow solenoid is operational and not blocking of the spray rinse requriement

Mar 23, 2015 | Miele Washing Machines

1 Answer

Miele W916 front-loading washing machine filling very slowly


Hi
There are two variant of this model one with normal fill hose and triple valve and one with waterproof system and triple valve. If you have change water proof hose (one with grey box on end) then it only leaves the triple valve.if waterproof hose is fitted be sure to order 110volt triple valve

Mar 05, 2010 | Miele Novotronic W1918A Front Load Washer

2 Answers

Miele Novatronic W360


there is still water in the waterproof tray at the bottom of the machine and the float switch has activated. pull the machine out (if pipes allow) and tip the machine backwards to drain the water from the tray.

Jun 01, 2008 | Miele Novotronic W1918A Front Load Washer

2 Answers

Miele novatronic w864 washing machine


Miele novatronic w864 washing machine.This video will show you how to keep your soap draw clear and how to service the parts
Please remember to subscribe to our YouTube channel for all appliance tutorials
a 4 THUMBS rating is appreciated for answering your FREE question.

Apr 28, 2008 | Miele W864 Front Load Washer

1 Answer

Leak from Novatronic W310


Bit the bullet and stripped out the covers from the unit so as to observe where the leak was coming from. Ran m/c on a basic quick wash (be careful, exposed live electrical terminals!!!) and noticed that water came from the detergent drawer for a second or two.
Stripped out detergent drawer housing and found that the large discharge pipe underneath was very blocked with black/white residue. Presume that this had been dislodged from the walls of the pipework during the house move.Removed residue and reassembled unit & ran, OK.
Saved myself £100 call out. Give Miele their due though, the documentation suggests that if you habitually wash at a low temperature, which we do, you should occasionally run a 95degree wash. My wife was very surprised when I asked her if she did this.

Apr 21, 2008 | Miele W310 Front Load Washer

Not finding what you are looking for?
Miele Novotronic Premier 500 Front Load Washer Logo

Related Topics:

488 people viewed this question

Ask a Question

Usually answered in minutes!

Top Miele Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1466 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

76673 Answers

Are you a Miele Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...