Question about Kenmore 24902 Top Load Washer

Open Question

I have kenmore 80 series model 110.29882890. How old is it?

It takes 27 minutes to fill. is that normal?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
AlmostBob
  • 550 Answers

SOURCE: Kenmore 80 Series - water wont fill to full load

remove edge decore trims from left and right side front of control panel8b608f8.jpg
remove phillips screws from bottom corners of contol panel
remove knob from water level selector
raise control panel ~1 inch then flip over backwords on pivots
depress lock tab on right/underside of water level control body where it touches metal mount plate
rotate water level control body 45deg anti clockwise
pull body off
top side of body next to knob shaft is 1/8 hex head bolt
turn clockwise to rais water level
anticlockwise to lower water level
machine can be operated with this part not fitted so can check level. fill, adjust screw, fill will start again, adjust screw, until water level is correct
reinstall in reverse order
Incidentally, the cause is a VERY small wire spring inside the control body that is not really up to the task, and stretches over years.
Its a common occurrence, and I make this repair, on callouts, no parts required, couple times a month you may have to flip the switch to reset to get the water to restart filling

Posted on Oct 25, 2008

Ad
  • 1 Answer

SOURCE: Kenmore 80 series won't spin

If it agitates and drains. leaving your clothes clean but soaking wet. It is most likely the transmission/gearbox. the motor is working otherwise it would not agitate. it is stuck in agitate mode and cannot "shift" into spin mode. new transmission will cost 140-170 and takes 2 or so hours to replace depending on skill level. total repair cost parts+labor $300ish you may want to ante up for a new machine at this point. if you cant to the labor yourself.
part# should be this: tho double check using your own model#
Part # AP3096209

Posted on Dec 09, 2008

  • 1 Answer

SOURCE: Kenmore 80 Series Top Load Washer not agitating

Check out this you tube. Had the same problem today. Tipped washer on its side and replaced coupler between motor and gearbox. Parts are about $15
This is a good diagnosis video.
http://www.youtube.com/watch?v=VYOP0_KCYT0

Posted on Dec 20, 2008

  • 58 Answers

SOURCE: kenmore 80 series model 110 after wash clothes are left soaking

when empty and off, open the lid and see if you can rotate the inner wash basket by hand. if you can easily, then the clutch is worn. This will prevent the basket from going into a high spin and wringing the clothes out. Replace the clutch by removing the top control panel, removing the clips that hold the cabinet, pull cabinet off, remove drain pump clips and pump, remove motor clips and motor, remove transmission (3 bolts). Now you will have access to the clutch, replace as needed, reverse dissasembly to complete. remember to unplug.

Posted on Jul 01, 2009

JULIANFIX
  • 975 Answers

SOURCE: How many cubic feet are in the Kenmore Washer Model 110 80 series

The cubic feet of the Kenmore washer model 110 heavy duty is 2.8 cubic feet. Measured to the top water line 14.5 inches and using the radius of the tub of 10.375 inches.

Posted on Oct 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Filling up with gas will keep stoping the gun


The most common cause is a venting problem in the tank, or a blockage in the filler pipe.

Feb 13, 2014 | 2000 Oldsmobile Intrigue

1 Answer

Kenmore series 80 model 110 wont stop filling!


There is a clear plastic hose that runs from the load selection switch to the side of the washer drum. This hose connects the fill sensor to the load switch. without it being in good condition and connected properly the washer won,t get a signal that it's full.

May 09, 2013 | Kenmore Washing Machines

1 Answer

Why does my Kenmore HE3t front load washer always take more time to finish then what it says on the timer?


Check the filters in both ends of the hoses. If they are clogged, it will throw the timer off. If it figures on 2 minutes to fill but it actually takes 6 or 7 minutes, the timer won't be accurate.

Jan 20, 2013 | Kenmore Elite 45986 Front Load Washer

1 Answer

Kenmore 80 series model # 110.82382110 fills, agitates and drains but won't spin


Based on the information you provided, you need to replace the wig wag on the unit. No joke, that is what the part is called. Here is a link to the part to order.


Nov 05, 2012 | Washing Machines

1 Answer

My kenmore 80 series washing machine makes a horrible noise and cold side fills about half speed when filling with water. What should I check?


For the slow water issue, you will need to replace the water inlet valve. Here is a link to the part.
Could you describe the noise and where it is coming from?

Oct 19, 2012 | Kenmore Washing Machines

1 Answer

Formatting Fujitsu HDD


certainly not.it is abnormal to take 20 hours which can be done in simply 5 minutes if you format it using Linux or just zero-fill your hard drive.do you know what is zero-filling?

Apr 03, 2012 | Fujitsu Computers & Internet

1 Answer

How long does it take to complete a wash cycle


Hello,

In a perfectly normal washer with decent incoming water pressure it should take 3-5 minutes to fill depending on water level size selected.

If what your experiencing is that your washer does fill yet it takes forever the problem is going to be with the water inlet valve.


GENE

Oct 04, 2011 | GE Profile WPRE6100G Top Load Washer

1 Answer

Take about 30 min to fill tank is this normal?


No. Normal would be one or two minutes. Either your piston is not sealing well, or the reed valve that acts as a one-way air ratchet is not sealing well. If it looses pressure while sitting idle, it's the reed valve.

Apr 13, 2011 | Coleman Powermate 27 Gallon Air Compressor

1 Answer

Kenmore Series 80 gas dryer, clothes take 3 hours to dry


Hello, This problem is going to be your safety valve coils...basically they get old and over time of heating then cooling develop a short when they heat up...It may appear the gas lights to start but then goes out until the safety valve coils cool back down. Here is a picture of the coils 57d5263.jpgThis The coils are mounted to the gas safety valve, This should solve your problem. Hope this helps, Please feel free to comment again if you have any further questions or concerns. Good Luck! Mike

Nov 04, 2009 | Kenmore Dryers

Not finding what you are looking for?
Kenmore 24902 Top Load Washer Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Sal DeAngelo

Level 3 Expert

2247 Answers

fordexpert

Level 3 Expert

5530 Answers

 Brian Main
Brian Main

Level 3 Expert

464 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...